Features

• It is an intermediate amplifier for the configuration where sensor signals are directly fed into a sequencer.
• To output sensor signals into a sequencer, this interface should be used together with the sensor so that it can lower the current to microamp level and amplify the signals enough to activate the sequencer.
• The outputs are transistor outputs, which means that it stays ON when the sensor is activated (detecting fluid).
• To prevent excessive vibration, silicone rubber is partially applied to this interface.
• The interface is available in 1, 4, 8, 16, and 24 points.

• The models in the table above are standard products with NPN transistor outputs.
• Products with model numbers that end with the letter P have PNP transistor outputs.
• PNP transistor output is available only for COT-5-4P.
• The models with PNP transistor outputs type have a circuit board which is the same size as those with NPN transistor outputs.

Drawing for Interface

Features

• While Lubrisensor was developed in order to detect micro flow rate and is available in only one diameter (PT1/8), fowsensor is available in PT 1/8, 1/4, and 3/8.
• The adjustable flow value model allows to adjust the flow value from a small to large value to serve the purpose.
• It can start sending a detection signal at a micro flow rate, passing a larger amount of oil/grease.
• Can also set the Sensor to send a signal when a large flow rate is decreased to the set micro flow rate.

Adjustable Flow Model

• Material (body)：aluminum, anodized surface
• Pressure 210kg／c㎡ MAX.
• Product comes with a standard 3m metal connector lead (which comes out from the top of the Sensor).
• Metal Connector Lead：1P×0.3mm2
  Outer diameter 4.0mm,
  heat resistant,
  oil resistant,
  flame retardant,
  flexible,
  black／white = + signal wire,
  black =－ground wire
• For grease, use CE－G, CK－G, and CL－G, which are specifically designed to detect grease.
• For harder grease, CE－G has the made-to-order models CE－G－K1, CE－G－K2, and CE－G－K3. CE－G－K3 is for the hardest. grease.

• Type CE ＝body weight 106g＋metal connector lead (standard, 3m) 68g＝Total weight 174g

• Type CK ＝body weight194g＋metal connector lead (standard, 3m) 78g＝ Total weight 272g

• Type CL ＝body weight 494g＋metal connector lead (standard, 3m) 78g＝ Total weight 572g

Features

• While Lubrisensor was developed in order to detect micro flow rate and is available in only one diameter (PT1／8), flowsensor is available in PT 1／8, 1／4, and 3／8 (the fixed flow value model is only available in PT1／8 and 1／4).
• Can also set the Sensor to send a signal when a large flow rate is decreased to the set micro flow rate.

Fixed Flow Model

• Material : brass
• Pressure : 210／c㎡ MAX
• Product comes with a standard 3m metal connector lead. The lead is also available in 5m, 8m and 10m.
• Metal Connector Lead : 1P×0.3mm2
  Outer diameter 4.0mm,
  heat resistant,
  oil resistant,
  flame retardant,
  flexible,
  black／white = + signal wire,
  black =－ground wire
• Type BM－C is also available in the flow rate threshold of 50cc/min and 100cc/min. Type KM－C is also available in 200cc/min.

• TYPE BM－C ＝Body weight 60g＋Metal connector lead (standard 3m) 76g＝Total weight 136g
• TYPE KM－C ＝Body weight 210g＋Metal connector lead (standard 3m) 68g＝Total weight 286g

Features

• It is the terminal micro flow sensors for lubricants and greases. 
• Lubrisensor detects even a very small amount of oil as well as checks its discharge amount.
• This means that it can be used with both resistance-type and fixed-type lubrication systems.
• This device is designed to be mounted on the terminal of a lubrication system.

Adjustable Flow Value Model

• Comes with a standard 3m lead. It is also available in 5m, 8m and 10m.

• In terms of performance, LUBSEN TYPE CA is equivalent to FLOSEN TYPE CE, while LUBSEN TYPE CB is equivalent to FLOSEN TYPE CE－G.
• As to made-to-order models, the performance of CB－K1 is equivalent to CE－G－K1, CB－K2 to CE－G－K2, and CB－K3 to CE－G－K3.

Features

• It is the terminal micro flow sensors for lubricants and greases. 
• Lubrisensor detects even a very small amount of oil as well as checks its discharge amount.
• This means that it can be used with both resistance-type and fixed-type lubrication systems.
• This device is designed to be mounted on the terminal of a lubrication system.

Fixed Flow Model

• This model is available in two types : TYPE BM for oil and for grease.
• BM type is the smallest sensor in the range.

From the table below (LUBSEN TYPE BM), please select the model that provides the desired sensitivity (standard flow rate threshold).

■For Oil

■For Grease

• The oil-resistant and waterproof metal connector connection can be removed for easy maintenance.
• BM-Type comes with a standard 3m metal connector lead. It is also available in 5m, 8m and 10m.
• Metal Connector Lead : 1P × 0.3mm²
  Outer Diameter 4.0mm
  Heat resistant
  Oil resistant
  Flame retardant
  Flexible
  Black/White = + signal wire
  Black = －ground wire
  

• Type FBM has a built-in coin filter in the “IN” side of the Sensor to prevent malfunction of the Sensor due to dust.
• This coin filter can be removed using tweezers for easy maintenance.

• Example : BM－10＝Body weight 60g＋Metal connector lead (standard：3m) 76g＝Total weight136g

LUBSEN Order Symbol

Example : 4φ－FBM－5－4φ－5M