Product features

● Easy to set and remove. No slipping by magnetic jig for an insert that contributes labor-saving. When demolding to the vertical direction, only pull up the product. For demolding to the horizontal direction, remove the anti-slipping pin then pull up.
● Easy maintenance of form panel. Only need to put a 5mm hole on the form panel, and it is easy to repair.
● Easy after treatment. After demolding, remove the HJ magnet jig from the concrete product by using a dedicated jig for the removal. We have a dedicated cap to filling holes as optional.

Specification

How to do setting, How to Use

Product features

● This is to be used as a countermeasure for salt damage as of bridge and other constructions by securing a certain level of a concrete cover, and easy to remove.

● When attaching with insert, the rubber deformed and tightlly connected, and secure a certain level of a concrete cover. The rubber corn is made by a special rubber. It will not remove even after fi lling with mortar.

● When demolding, the rubber form goes back to the original and easy to remove. It can be used continuously so it is an economical product

Specification

How to do setting

How to Use

Product features

● Create a tiny rib at the middle of the threaded part and headed part of the jig in order to use at the side of the form panel.

● It is no need to remove the jig from the form panel when demolding, the shear created by demolding would break a slitted part of the jig.

● It would be possible to attach inserts only at the surface side of the form panel, which enables a one-person work.

Application

Attachment of insert to the place out of reach that unable to either set or remove insert by bolt on form panel.

Specification

How to do setting, How to Use

Product features

● Add a rib at the center of the jig with a small slit in order to apply at the side of the form panel.

● It is no need to remove the jig from the form panel when demolding, the shear created by demolding would break a slitted part of the jig.

● It would be possible to attach inserts only at one side of the form panel, which enables a one-person work

Application

Attachment of insert to the place out of reach that unable to either set or remove insert by bolt on form panel.

Specification

How to do setting, How to Use

Product feature

● Create a thread in A jig cap so that fills the gap of the diameter of the threaded hole of inserts that enables to use with all of the inserts.

Application

Attachment of insert to the place out of reach that unable to either set or remove insert by bolt on form panel.

Specification

How to do setting, How to Use

Product features

● Use magnet to attach inserts with form panel so that can avoid using bolts that let reduce the labor of drive screws which enable the drastically reduce the labor cost.

● This may be able to avoid the risk of a worker going into the back and below of the form panel.

● Deterioration of magnet is not so mush and the yoke is also solid and strong that enable to use for semi-permanently.

Specification

How to do setting, How to Use

Product features

● Enable the easy connection of hume pipe and pile with form panel.

● The product is matched especially to a form panel that has many mounting locations by shortening a mounting time and loss prevention of bolt and nut.

● The replacement of components is available.

Specification

How to do setting, How to Use

Product features

● This is to make the concrete cover.

● Please use double-sided tape when you would like to set inserts without making a hole on the form panel.

Specification

How to do setting, How to Use

Product features

● This is the one to enable an insert to be set to the composite panel which can not directly fix by the bolt.

● It enables to avoid making a big hole on a panel when putting insert.

● It enables to avoid making a big hole on a panel when

Specification

How to do setting, How to Use

Product features

● Is able to work only by one person instead of two, which enables to reduce the cost of the workforce.

● The worker can handle the product easily that the work efficiency increases a lot.

● It is able to be installed in an area that is difficult to use bolts.

Specification

How to do setting, How to Use

Product features

● This is the one to enable an insert to be set to the composite panel which can not directly fix by the bolt.

● Enable to remain the surface of insert (screw part) by the same level with the concrete surface.

● Hole filling type can fill the holes that used to drill on form panel.

Specification

How to do setting, How to Use

Product features

● In general, we use tapping to set duct sleeves. But this way, we needed to do the tapping whenever the place of the duct sleeve change which made the composite panel many holes. It leads the durability of composite panels shorter. CBM jig can solve the issues and it also is able to avoid making holes on a composite panels.

● It is able to use for an Electrical box/Sleeve. (for construction).

Specification

How to do setting, How to Use

Product features

● This is to use as the attachment of a fine ceramic insert.

Specification

How to do setting, How to Use

Product features

● When using a general bolt to do the setting, normally need to make a hole of the size more than the bolt but by using a C jig, we only need to make a hole with a small size.

●The surface of the insert thread will be the same with the concrete surface.

Specification

How to do setting, How to Use

Product features

● When using a general bolt to do the setting, normally need to make a hole of the size more than the bolt but by using a B jig, we only need to make a hole with a small size that can minimize the damage on the mold.

● This is the one to pull in the thread of insert from the concrete surface

Specification

How to do setting, How to Use

Product features

● During the setting of an insert with a mold, when a bolt cannot directly connect, this is the one to use.

● This can provide a gap from the surface of the insert thread to the concrete surface.

Specification

How to do setting, How to Use

Specifications