─

─

Unit/Unit	M1.7	M2	M2.5	M2.6	M3	M4
N m	0.041	0.101	0.24	0.22	0.36	0.85
Unit/Unit	M5	M6	M8	M10	M12	M16
N m	1.65	2.74	6.22	11.39	15.93	38.9

• Common type for plastic screws and metal screws.
•  A set of hex bolt cap and lid.
  ・Screws are sold separately.
• There may be some wobbling, but this will not cause any problems in use.
  ・ Common type of plastic screw and metal screw.
  ・ Set of cover and cap of hexagon bolt.
  ・ Screws are sold separately.
  ・ Although there may be misalignment to some extent, it does not pose any problem in use.

Sales unit Quantity

Torsional rupture torque

Tensile rupture force

We accept orders starting from 1 piece. It is possible to change the L dimension by cutting, so please contact us if necessary.
We accept orders starting from one unit.
Since L shape dimensions can be changed during cutting, please discuss if required.

Sales unit Quantity

Torsional rupture torque

Unit/Unit	M1.7	M2	M2.5	M2.6	M3	M4
N m	0.022	0.055	0.13	0.12	0.18	0.39
Unit/Unit	M5	M6	M8	M10	M12	M16
N m	0.8	1.2	3.2	6.38	10.35	–

Tensile rupture force

Unit/Unit	M1.7	M2	M2.5	M2.6	M3	M4
N	51	107	176	196	266	481
Unit/Unit	M5	M6	M8	M10	M12	M16
N	797	1136	2088	3363	4953	–

• We use raw materials that are RoHS2 compliant.
• Black spots (sludge) may appear on the exterior.
• The remaining gate at the screw tip is less than 5% of the length (L).

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

• We use raw materials that are RoHS2 compliant.
• Black spots (sludge) may appear on the exterior.
• The remaining gate at the screw tip is less than 5% of the length (L).
• Please use in combination with a nut made of the same material as the thread pitch may shift during molding.
• If a nut is not used, the fit with the female thread should be 20 mm or less.

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

Petal washer is a new type of screw cover which will not drop off like a screw cap.

Petal washer is non-conductive, decorative, provides heat insulation, simple security, and screw

head protection.

M		M4	M8
─	─	100	100

Sales unit Quantity

We use raw materials that are RoHS2 compliant.

Features

• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

These are resin rivets for attaching panels, etc. By pushing in with your fingertips, the legs are spread apart and the panel etc. is fixed. It can also be removed using a screwdriver.
PC+PP/HR-P is plastic rivet for the panel mounting. Stretch out feet part by hammer a nail into panel. It is possible to take out by driver.

Sales unit Quantity

Torsional rupture torque

Tensile rupture force

─

─

• We use raw materials that are RoHS2 compliant.
• There may be black spots (sludge) on the exterior.
• Please use in combination with a nut made of the same material as the thread pitch may shift during molding.
• If a nut is not used, the fit with the female thread should be 20 mm or less.
• The remaining gate at the screw tip is less than 5% of the length (L).

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

• We use raw materials that are RoHS2 compliant.
• Black spots (sludge) may appear on the exterior.
• The remaining gate at the screw tip is less than 5% of the length (L).
• Please use in combination with a nut made of the same material as the thread pitch may shift during molding.
• If a nut is not used, the fit with the female thread should be 20 mm or less.

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

We use raw materials that are RoHS2 compliant.

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

Nominal diameter 3 has the same shape as the set washer for self-tapping screws.
For nominal diameter 8, there are 6 protrusions on the inner diameter.
When assembling, please screw it in.
Nominal diameter 3 has same configuration as set washer for tapping screw.
Nominal diameter 8 has six inner diameter protruding portions.
Please use to screw in when you built-in.

Sales unit Quantity

We use raw materials that are RoHS2 compliant.

Features

• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

• We use RoHS2 compliant raw materials.
• There may be black spots (sludge) on the exterior.
• The remaining gate at the screw tip is less than 5% of the length (L).
• Please use in combination with a nut made of the same material as the thread pitch may shift during molding.
• If a nut is not used, the fit with the female thread should be 20 mm or less.

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• The washer may warp slightly.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

• We use raw materials that are RoHS2 compliant.

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

• We use raw materials that are RoHS2 compliant.
• There may be black spots (sludge) on the exterior.
• Please use in combination with a nut made of the same material as the thread pitch may shift during molding.
• If a nut is not used, the fit with the female thread should be 20 mm or less.
• The remaining gate at the screw tip is less than 5% of the length (L).

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

• We use raw materials that are RoHS2 compliant.
• Black spots (sludge) may appear on the exterior, but this does not affect performance.
• Please use in combination with a nut made of the same material as the thread pitch may shift during molding.
• If a nut is not used, the fit with the female thread should be 20 mm or less.
• The remaining gate at the screw tip is less than 5% of the length (L).

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

• We use raw materials that are RoHS2 compliant.
• Black spots (sludge) may appear on the exterior.
• The remaining gate at the screw tip is less than 5% of the length (L).
• Please use in combination with a nut made of the same material as the thread pitch may shift during molding.
• If a nut is not used, the fit with the female thread should be 20 mm or less.

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

• We use raw materials that are RoHS2 compliant.
• Black spots (sludge) may appear on the exterior.
• The remaining gate at the screw tip is less than 5% of the length (L).
• Please use in combination with a nut made of the same material as the thread pitch may shift during molding.
• If a nut is not used, the fit with the female thread should be 20 mm or less.

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

• We use raw materials that are RoHS2 compliant.
• Black spots (sludge) may appear on the exterior.
• The remaining gate at the screw tip is less than 5% of the length (L).

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

• We use raw materials that are RoHS2 compliant.
• Black spots (sludge) may appear on the exterior.
• The remaining gate at the screw tip is less than 5% of the length (L).

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

• We use raw materials that are RoHS2 compliant.
• Black spots (sludge) may appear on the exterior.
• The remaining gate at the screw tip is less than 5% of the length (L).

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

• We use raw materials that are RoHS2 compliant.
• Black spots (sludge) may appear on the exterior.
• The remaining gate at the screw tip is less than 5% of the length (L).

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

• We use raw materials that are RoHS2 compliant.
• Black spots (sludge) may appear on the exterior.
• The remaining gate at the screw tip is less than 5% of the length (L).

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.

─

─

─

─

We use raw materials that are RoHS2 compliant.

Features

• The values ​​in the table are reference values ​​and are not guaranteed values.
• Please use a torque driver and torque wrench for tightening. The recommended tightening torque is 50% of the breaking torque value under use.
• Heat resistance and chemical resistance vary depending on usage conditions, so be sure to test under usage conditions beforehand.
• There may be slight discoloration depending on the lot and various conditions.
• Inventory sizes, shapes, and manufacturers of materials used are subject to change without notice.