Suntes | Kouei Japan Trading | Get Quotation

Suntes SE type Ball clutch/release type cartridge

kvtpart — Mon, 28 Dec 2020 04:56:52 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)

Structure and operating principle

Torque is transmitted by the ball ② pressed into the hole by the force of the torque transmission spring (Fig. 1).
When torque exceeding the overload
setting is applied, the ball ② escapes from the hole against the spring force and is allowed to rotate freely by the retention mechanism (Fig. 2).
Simply align the reset
position mark and then push in the plunger ③ to reset it easily.
The sensor can be activated by the protruding action of the overload sensing plunger.
Turning the adjuster ④ inside the torque adjustment
element to the right increases the transmitted torque. This is done with the element removed from the flange. This is to prevent an outsider from accidentally moving the adjuster and causing an accident.
Free rotation retention mechanismAfter
an overload, the torque releaser rotates freely.This is because when the ball ② escapes from the hole ①, the plunger ③ is pushed backwards, and the small ball ⑦ on its circumference is pushed into the angle race (6 x 8) against the force of the spring ⑤, as shown in Figure 2, and the thrust of the plunger no longer acts.

Size

The dimensional drawing is for the coupling type.

Model	A	B	L	C	D	E	F	G	H	J	K	M	N
TE-1411	100	102	302	360	300	120	27	85	124.5	53	58.5	6.5	4
TE-1611	112	104	328	360	300	143	42	100	137.5	53	58.5	6.5	6
TE-2315	125	104	354	470	390	165	42	115	131	92	77	8	3
TE-2415	140	106	386	470	390	190	45	135	147	92	77	8	4
TE-2518	170	108	448	540	460	224	88	160	178	92	77	8	5
TE-2618	190	108	488	540	460	250	103	180	198	92	77	8	6
TE-2721	200	110	510	620	540	280	118	200	209	92	77	8	7
TE-3322	224	115	563	710	580	320	137	225	235	93	139	14	3
TE-3425	250	155	655	790	660	350	157	250	281	93	139	14	4
TE-3628	280	171	731	850	720	395	187	280	319	93	139	14	6
TE-3631	315	171	801	920	790	450	317	320	354	93	139	14	6
TE-3833	355	171	881	970	840	505	247	360	394	93	139	14	8

Specification

Model	Set torque MAX(Nm)	P Safety element type
TE-1411	7,000	#10
TE-1611	10,600	#10
TE-2315	19,000	#20
TE-2415	25,300	#20
TE-2518	37,300	#20
TE-2618	44,700	#20
TE-2721	61,300	#20
TE-3322	97,500	#30
TE-3425	148,000	#30
TE-3628	242,000	#30
TE-3631	265,000	#30
TE-3833	376,600	#30

We also respond to special specifications.
If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes SE type Ball clutch/release type cartridge first appeared on Kouei Japan Trading | Get Quotation.

Suntes TVDW type Cassette pin type

kvtpart — Mon, 28 Dec 2020 04:43:47 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: TVDW

Size

Model	D0	D1	D2	D3	D4	L1	L2	L3	L4	PCD	Nd
TV30DW	15	30	70	120	135	18	63	12	3	95	4-M8
TV40DW	15	40	95	145	160	twenty three	68	12	3	120	8-M10
TV60DW	20	60	130	190	210	twenty three	90	15	5	160	8-M12
TV70DW	40	70	145	215	234	33	100	15	5	180	8-M14
TV80DW	50	80	160	235	254	40	125	15	5	200	8-M14
TV95DW	58	95	195	280	305	50	155	15	5	230	8-M16
TV110DW	80	110	230	320	348	50	180	15	5	270	8-M20
TV120DW	80	120	256	350	378	60	190	15	5	310	8-M20
TV160DW	80	160	310	420	448	85	215	15	5	380	8-M24

Specification

Model	Maximum RPM(min ^-1 )	Maximum torque(Nm)	Product weight(kg)
TV30DW	100	500	4.5
TV40DW	100	1,000	7.1
TV60DW	100	1,500	17
TV70DW	100	2,000	twenty three
TV80DW	100	4,000	34
TV95DW	100	8,000	60
TV110DW	100	15,000	92
TV120DW	100	20,000	118
TV160DW	100	35,000	186

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes TVDW type Cassette pin type first appeared on Kouei Japan Trading | Get Quotation.

Suntes Structure and operating principle TY type torque reliever

kvtpart — Mon, 28 Dec 2020 04:16:43 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)

Part Names

Hub Boss
Flanges
bearing
C-shaped retaining ring for holes
case
C-shaped retaining ring for shaft
WR type retaining ring
Hexagonal Socket Set Screw
Steel ball
Parallel pin
segment
Tapered Ring
Slide Ring
Adjustable Ring
metal
clip
pin
Spring
Spring

Operation

During normal operation, the steel ball ⑨ held by the hub boss ① is pressurized and held in the ball pocket of the flange ② by the force of the spring ⑲, and torque is transmitted from the hub boss ① via the steel ball ⑨ to the flange ②.
In the event of an overload, the steel ball ⑨ is pushed out by the slope of the ball pocket of the flange ②, cutting off the transmitted torque. At the same time, the segment ⑪ moves up the slope of the hub boss protrusion against the force of the spring ⑲, pushing apart the case ⑤ and tapered ring ⑫ and reaching the top of the hub boss protrusion. This removes the force pressing the steel ball ⑨ into the ball pocket of the flange ②, allowing the flange ② to rotate freely on the bearing ③. At this time, the case ⑤ also moves axially (towards the adjusting ring ⑭), and this action can be used to detect an overload with a limit switch, proximity switch, etc.
To restart the machine, after eliminating the cause of the overload, rotate either the input or output side of the torque releaser until the alignment marks on the hub boss ① and flange ② are aligned, and then press the case ⑤ against the flange ② to reset it.

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes Structure and operating principle TY type torque reliever first appeared on Kouei Japan Trading | Get Quotation.

Suntes Roller chain sprockets TY type torque reliever

kvtpart — Mon, 28 Dec 2020 04:11:01 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)

Compatible sprockets

Model	#40	#50	#60	#80	#100	#120	#140
TY30-A	30 to 55T	25 to 45T	21 to 37T
TY30-D	32 to 55T	30-45T	23 to 37T
TY40-A		30 to 54T	25 to 45T	20 to 33T
TY40-D		30 to 54T	26 to 45T	20 to 33T
TY50-A			29 to 55T	23 to 41T	19 to 33T
TY50-D			32 to 55T	25 to 41T	21 to 33T
TY65-A				28～51T	23 to 41T	20 to 34T	18 to 29T
TY85-A				36 to 66T	29 to 53T	25 to 44T	22 to 37T

Sprocket machining dimensions

Model	A	B	C	D	EF	G	H	I
TY30-A	105H7+0.035 -0	75 or less	5	90	6-6.6	~	▽▽	▽▽▽
TY30-D	114	85H7+0.035 -0	5	100	6-6.6	▽▽▽	▽▽	▽
TY40-A	130H7+0.040 -0	Below 95	5	115	6-9	~	▽▽	▽▽▽
TY40-D	135	105H7+0.035 -0	5	120	6-9	▽▽▽	▽▽	▽
TY50-A	155H7+0.040 -0	Under 115	8	135	6-11	~	▽▽	▽▽▽
TY50-D	169	130H7+0.040 -0	8	150	6-11	▽▽▽	▽▽	▽
TY65-A	198H7+0.046 -0	Under 150	8	175	6-14	~	▽▽	▽▽▽
TY85-A	258H7+0.052 -0	Under 200	8	230	6-18	~	▽▽	▽▽▽

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes Roller chain sprockets TY type torque reliever first appeared on Kouei Japan Trading | Get Quotation.

Suntes ON/OFF Shifter TY Type Torque Reliever

kvtpart — Mon, 28 Dec 2020 04:03:36 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: TY type

Dimension

Model	A	B	C	D	E	F	G	H	L	M	N	P
TY30	120	189	70	100	55	75	169	45.5	124	169	15	150
TY40	140	219	90	120	65	90	177	46.5	147	177	15	192
TY50	180	266	90	120	80	110	182	56.0	152	182	17.5	214
TY65	220	321	105	145	100	130	222	64.5	182	222	22.5	236
TY85	290	398	140	185	100	130	246	91.0	201	246	25	294

Model	Q	R	S	T	U	V	W	φX	φY	φD0	Air Cylinder specification (φmm)
TY30	130	20	90	135	18	263	55	10	11	150	63 × 30ST
TY40	166	twenty five	110	165	twenty five	325	75	12	13.5	175	80 x 30ST
TY50	188	30	130	195	twenty five	380	75	14	13.5	210	100 x 35ST
TY65	203	35	150	225	32	442	85	14	18	250	125 x 45ST
TY85	253	35	190	285	40	550	130	18	twenty two	330	160 x 50ST

The post Suntes ON/OFF Shifter TY Type Torque Reliever first appeared on Kouei Japan Trading | Get Quotation.

Suntes TYAR type Manual reset type

kvtpart — Mon, 28 Dec 2020 03:47:54 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: TYAR

Part Names

Hub Boss
Flanges
bearing
C-shaped retaining ring for holes
case
C-shaped retaining ring for shaft
WR type retaining ring
Hexagonal Socket Set Screw
Steel ball
Parallel pin
segment
Tapered Ring
Slide Ring
Adjustable Ring
metal
clip
pin
Spring
Model plate
Nameplate
Spring
Coupling
Hexagonal Socket Set Screw

Size

Model	A	B	C	D	E	φF	φG	φH	φJ
TY30AR-L/H/G	180	58	106	12	40.4	155	70	102	150
TY40AR-L・H・G	203	64	119	12	42.3	175	85	122	175
TY50AR-L/H/G	240	76	140	16	49.9	205	100	147	210
TY65AR-L/H/G	287	92	165	20	56.7	260	125	183	250
TY85AR-L/H/G	363	108	220	20	84.3	340	160	232	330

Specification

Torque Releasor

Model	Torque setting range (Nm)	Spring color x number	Maximum RPM (min ^-1 )	Moment of inertia (kg ^m2 )	Product weight (kg)
TY30AR-L	26～94	White × 16	2,200	20× ^10-3	9.0
TY30AR-H	43～170	Red × 8
TY30AR-G	89～200	Red × 16
TY40AR-L	56～180	White × 16	1,800	44× ^10-3	15.0
TY40AR-H	67～400	Red × 8
TY40AR-G	160 to 400	Red × 16
TY50AR-L	50～290	White × 16	1,800	107× ^10-3	27.0
TY50AR-H	100 to 520	Red × 8
TY50AR-G	180 to 800	Red × 16
TY65AR-L	110～440	White × 16	1,800	319× ^10-3	59.0
TY65AR-H	270～1,200	Red × 8
TY65AR-G	580 to 1,600	Red × 16
TY85AR-L	290-1,000	Yellow × 16	1,800	1,113× ^10-3	106.0
TY85AR-H	580 to 2,000	Red × 8
TY85AR-G	1,100～3,200	Red × 16

Model	Maximum shaft hole diameter (φmm)	Standard shaft hole diameter (φmm)	Pilot hole diameter (φmm)	Set screw	OverloadsShift Dimensions (mm)
TY30AR-L/H/G	30	30H7×8Js9	19	2-M4	2.4
TY40AR-L・H・G	40	40H7×12Js9	twenty four	2-M5	2.8
TY50AR-L/H/G	50	50H7×14Js9	34	2-M6	3.6
TY65AR-L/H/G	65	65H7×18Js9	38	2-M10	4.8
TY85AR-L/H/G	85	85H7×22Js9	48	2-M12	5.8

Coupling

Model	Maximum shaft hole diameter(φmm)	Pilot hole diameter(φmm)	setscrew
TY30AR-L/H/G	48	15	2-M4
TY40AR-L・H・G	55	15	2-M5
TY50AR-L/H/G	65	20	2-M6
TY65AR-L/H/G	85	30	2-M10
TY85AR-L/H/G	115	40	2-M12

Characteristic Curve

The torque can be changed in proportion to the number of springs. A minimum of three springs can be used.

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes TYAR type Manual reset type first appeared on Kouei Japan Trading | Get Quotation.

Suntes TY D type Manual reset type

kvtpart — Mon, 28 Dec 2020 03:31:59 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: D

Part Names

Hub Boss
Thrust Ring
Flanges
metal
case
C-shaped retaining ring for shaft
WR type retaining ring
Hexagonal Socket Set Screw
Steel ball
Parallel pin
segment
Tapered Ring
Slide Ring
Adjustable Ring
metal
clip
pin
Spring
Model plate
Nameplate
Spring

Size

Model	A	B	C	D	E	φF	φG	φH	φJ	Mounting bolts
Model	A	B	C	D	E	φF	φG	φH	φJ	K PCD	L Bolt size
TY30D-L・H・G	85	15	9	12	40.4	113	85+0 -0.035	102	150	100	6-M6
TY40D-L・H・G	95	18	10	12	42.3	134	105+0 -0.035	122	175	120	6-M8
TY50D-L・H・G	115	twenty four	10	16	49.9	168	130+0 -0.040	147	210	150	6-M10

Specification

Model	Torque setting range (Nm)	Spring color x number	Maximum RPM (min ^-1 )	Moment of inertia (kg ^m2 )	Product weight (kg)
TY30D-L	26～94	White × 16	400	7.6× ^10-3	4.0
TY30D-H	43～170	Red × 8
TY30D-G	89～200	Red × 16
TY40D-L	56～180	White × 16	310	17.7× ^10-3	7.0
TY40D-H	67～400	Red × 8
TY40D-G	160 to 400	Red × 16
TY50D-L	50～290	White × 16	240	46.9× ^10-3	14.0
TY50D-H	100 to 520	Red × 8
TY50D-G	180 to 800	Red × 16

Model	Maximum shaft hole diameter (φmm)	Standard shaft hole diameter (φmm)	Pilot hole diameter (φmm)	Set screw	OverloadsShift Dimensions (mm)
TY30D-L・H・G	30	30H7×8Js9	19	2-M4	2.4
TY40D-L・H・G	40	40H7×12Js9	twenty four	2-M5	2.8
TY50D-L・H・G	50	50H7×14Js9	34	2-M6	3.6

Characteristic Curve

The torque can be changed in proportion to the number of springs. A minimum of three springs can be used.

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes TY D type Manual reset type first appeared on Kouei Japan Trading | Get Quotation.

Suntes TY A type Manual reset type

kvtpart — Mon, 28 Dec 2020 03:16:47 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: A

Part Names

Hub Boss
Flanges
bearing
C-shaped retaining ring for holes
case
C-shaped retaining ring for shaft
WR type retaining ring
Hexagonal Socket Set Screw
Steel ball
Parallel pin
segment
Tapered Ring
Slide Ring
Adjustable Ring
metal
clip
pin
Spring
Model plate
Nameplate
Spring

Size

Model	A	B	C	D	φE	φF	φG	φH	Mounting bolts
Model	A	B	C	D	φE	φF	φG	φH	J PCD	K Bolt size
TY30A-L・H・G	110	4	12	40.4	105+0 -0.035	75+0.030 -0	102	150	90	6-M6×12L
TY40A-L・H・G	one two three	4	12	42.3	130+0 -0.040	95+0.035 -0	122	175	115	6-M8×16L
TY50A-L・H・G	145	5	16	49.9	155+0 -0.040	115+0.035 -0	147	210	135	6-M10×20L
TY65A-L・H・G	170	5	20	56.7	198+0 -0.046	150+0.040 -0	183	250	175	6-M12×24L
TY85A-L・H・G	225	5	20	84.3	258+0 -0.046	200+0.046 -0	232	330	230	6-M16×32L

Specification

Model	Torque setting range (Nm)	Spring color x number	Maximum RPM (min ^-1 )	Moment of inertia (kg ^m2 )	Product weight (kg)
TY30A-L	26～94	White × 16	2,200	9.3× ^10-3	5.0
TY30A-H	43～170	Red × 8
TY30A-G	89～200	Red × 16
TY40A-L	56～180	White × 16	1,800	22× ^10-3	8.0
TY40A-H	67～400	Red × 8
TY40A-G	160 to 400	Red × 16
TY50A-L	50～290	White × 16	1,800	56.7× ^10-3	16.0
TY50A-H	100 to 520	Red × 8
TY50A-G	180 to 800	Red × 16
TY65A-L	110～440	White × 16	1,800	155.2× ^10-3	37.0
TY65A-H	270～1,200	Red × 8
TY65A-G	580 to 1,600	Red × 16
TY85A-L	290-1,000	Yellow × 16	1,800	566× ^10-3	64.0
TY85A-H	580 to 2,000	Red × 8
TY85A-G	1,100～3,200	Red × 16

Model	Maximum shaft hole diameter (φmm)	Standard shaft hole diameter (φmm)	Pilot hole diameter (φmm)	Set screw	OverloadsShift Dimensions (mm)
TY30A-L・H・G	30	30H7×8Js9	19	2-M4	2.4
TY40A-L・H・G	40	40H7×12Js9	twenty four	2-M5	2.8
TY50A-L・H・G	50	50H7×14Js9	34	2-M6	3.6
TY65A-L・H・G	65	65H7×18Js9	38	2-M10	4.8
TY85A-L・H・G	85	85H7×22Js9	48	2-M12	5.8

Characteristic Curve

The torque can be changed in proportion to the number of springs. A minimum of three springs can be used.

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes TY A type Manual reset type first appeared on Kouei Japan Trading | Get Quotation.

Suntes Structure and operating principle

kvtpart — Mon, 28 Dec 2020 02:41:58 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)

Part Names

Hub Boss
Flanges
Action Ring
Spring
key
Steel ball
bearing
Washer
Adjustable Ring
Hexagonal Socket Set Screw
ring
WR type retaining ring
pin
Spring

Operation

During normal operation, the steel ball ⑥ held by the flange ② is pressurized and held in the ball pocket of the hub boss ① by the force of the spring ④, and torque is transmitted from the hub boss ① to the flange ② via the steel ball ⑥.
In the event of an overload, the steel ball ⑥ is pushed out by the slope of the ball pocket of the hub boss ①, cutting off the transmitted torque. At this time, the action ring ③ moves in the axial direction (towards the adjustment ring ⑨), and this movement can be used to detect an overload with a limit switch, proximity switch, etc.
When restarting the machine, after removing the cause of the overload, rotate the input or output side of the torque releaser. When the steel ball reaches the specified ball pocket position (one position per rotation), it will be automatically reset by the force of spring ④.

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes Structure and operating principle first appeared on Kouei Japan Trading | Get Quotation.

Suntes Roller Chain Sprockets

kvtpart — Mon, 28 Dec 2020 02:18:57 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)

Compatible sprockets

Model	#35	#41	#40	#50	#60	#80	#100	#120	#140
TX15-D	27～46T	21 to 35T	21 to 35T
TX15-E	27～46T	21 to 35T	21 to 35T
TX20-D		26 to 45T	26 to 45T	21 to 36T
TX20-E		25 to 45T	25 to 45T	21 to 36T
TX30-D			32 to 55T	26 to 45T	23 to 37T
TX30-E			30 to 55T	25 to 45T	21 to 37T
TX40-D				30 to 54T	26 to 45T	20 to 33T
TX40-E				29 to 54T	25 to 45T	20 to 33T
TX50-D					32 to 55T	25 to 41T	21 to 32T
TX50-E					29 to 55T	23 to 41T	19 to 32T
TX65-E						28～51T	23 to 41T	20 to 34T	18 to 29T
TX85-E						35～66T	29 to 53T	25 to 44T	22 to 37T

Sprocket machining dimension

Model	A	B	C	D	EF	G	H	I
TX15-D	70	50H7+0.025 -0	3	60	6-5.5	▽▽▽	▽▽	▽
TX15-E	70	35H7+0.025 -0	3	58	6-5.5	▽▽▽	▽▽	▽
TX20-D	89	65H7+0.030 -0	3	75	6-6.6	▽▽▽	▽▽	▽
TX20-E	86	45H7+0.025 -0	3	72	6-6.6	▽▽▽	▽▽	▽
TX30-D	114	85H7+0.035 -0	5	100	6-6.6	▽▽▽	▽▽	▽
TX30-E	105	60H7+0.030 -0	5	90	6-6.6	▽▽▽	▽▽	▽
TX40-D	135	105H7+0.035 -0	5	120	6-9	▽▽▽	▽▽	▽
TX40-E	127	75H7+0.030 -0	5	110	6-9	▽▽▽	▽▽	▽
TX50-D	169	130H7+0.040 -0	8	150	6-11	▽▽▽	▽▽	▽
TX50-E	156	90H7+0.035 -0	8	135	6-11	▽▽▽	▽▽	▽
TX65-E	199	120H7+0.035 -0	8	175	6-14	▽▽▽	▽▽	▽
TX85-E	255	150H7+0.040 -0	8	225	6-18	▽▽▽	▽▽	▽

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes Roller Chain Sprockets first appeared on Kouei Japan Trading | Get Quotation.

Suntes TX R type Automatic reset type

kvtpart — Mon, 28 Dec 2020 01:25:21 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: R

Part Names

Hub boss
Flange
Action ring
Plate
Hexagon socket plug
Hexagon socket bolt
Coupling
Spring
Key
Steel ball
Bearing
Washer
Adjusting ring
Hexagon socket set screw
Ring
WR-type retaining ring
Pin
Spring
Model nameplate
Nameplate
Hexagon socket set screw

Size

Model	A	B	C	D	E	φF	φG	φH	φJ
TX15R-L・H・G	88	38	50	4	13.7	100	45	56	96
TX20R-L・H・G	99	44	55	4	15.1	125	60	68	108
TX30R-L・H・G	126	58	68	6	20.0	155	70	84	124
TX40R-L・H・G	148	64	84	6	20.3	175	85	108	148
TX50R-L・H・G	175	76	99	8	24.8	205	100	134	174
TX65R-L・H・G	215	92	123	8	29.9	260	125	172	212
TX85R-L・H・G	248	108	140	10	36.5	340	160	218	258

Specification

Torque Releaser

Model	Torque setting range （N・m）	Spring color x number	Maximum RPM （min^-1）	Moment of inertia (kg ^m2 )	Product weight （kg）
TX15R-L	7～24	White × 10	900	1.6×10^-3	2.3
TX15R-H	8～38	Red × 5
TX15R-G	13～50	Red × 10
TX20R-L	12～43	White × 12	750	4.0×10^-3	3.8
TX20R-H	16～70	Red × 6
TX20R-G	40～100	Red × 12
TX30R-L	14～72	white × 12	600	11.4×10^-3	7.2
TX30R-H	33～170	Red × 6
TX30R-G	72～200	Red × 12
TX40R-L	20～160	White × 12	450	24.7×10^-3	11.4
TX40R-H	43～330	Red × 6
TX40R-G	97～400	Red × 12
TX50R-L	79～390	White × 12	400	70.4×10^-3	22.0
TX50R-H	130～580	Red × 6
TX50R-G	280～800	Red × 12
TX65R-L	80～480	White × 12	300	207.1×10^-3	46.8
TX65R-H	200～1,000	Red × 6
TX65R-G	570～1,600	Red × 12
TX85R-L	270～1,100	Red × 12	200	662.6×10^-3	77.8
TX85R-H	450～2,100	Red × 6
TX85R-G	1,300～3,200	Red × 12

Model	Maximum shaft hole diameter (φmm)	Standard shaft hole diameter (φmm)	Pilot hole diameter (φmm)	Set screw	OverloadsShift Dimensions (mm)
TX15R-L・H・G	15	15H7×5Js9	9	2-M4	1.5
TX20R-L・H・G	20	20H7×6Js9	12	2-M4	1.9
TX30R-L・H・G	30	30H7×8Js9	19	2-M4	2.6
TX40R-L・H・G	40	40H7×12Js9	24	2-M5	2.9
TX50R-L・H・G	50	50H7×14Js9	34	2-M8	3.8
TX65R-L・H・G	65	65H7×18Js9	38	2-M10	5.0
TX85R-L・H・G	85	85H7×22Js9	48	2-M12	6.0

Coupling

Model	Maximum shaft hole diameter (φmm)	Pilot hole diameter (φmm)）	Set screw
TX15R-L・H・G	30	12	2-M4
TX20R-L・H・G	38	12	2-M4
TX30R-L・H・G	48	15	2-M4
TX40R-L・H・G	55	15	2-M5
TX50R-L・H・G	65	20	2-M8
TX65R-L・H・G	85	30	2-M10
TX85R-L・H・G	115	40	2-M12

Characteristic Curve

The torque can be changed in proportion to the number of springs. A minimum of three springs can be used.

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes TX R type Automatic reset type first appeared on Kouei Japan Trading | Get Quotation.

Suntes TX E type Automatic reset type

kvtpart — Mon, 28 Dec 2020 01:11:05 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: E

Part Names

Hub Boss
housing
Hexagonal Socket Head Bolt
Spring pin
Flanges
Hexagonal Socket Plug
metal
Action Ring
Spring
key
Steel ball
bearing
Washer
Adjustable Ring
Hexagonal Socket Set Screw
ring
WR type retaining ring
pin
Spring
Model plate
Nameplate

Size

Model	A	B	C	D	E	φF	φG	φH	Mounting bolts
Model	A	B	C	D	E	φF	φG	φH	J PCD	K Bolt size
TX15E-L・H・G	3	52	4	13.7	69	35+0 -0.025	56	96	58	6-M5×15L
TX20E-L・H・G	3	62	4	15.1	85	45+0 -0.025	68	108	72	6-M6×20L
TX30E-L・H・G	3	77	6	20.0	104	60+0 -0.030	84	124	90	6-M6×23L
TX40E-L・H・G	3	87	6	20.3	126	75+0 -0.030	108	148	110	6-M8×25L
TX50E-L・H・G	3	107	8	24.8	155	90+0 -0.035	134	174	135	6-M10×32L
TX65E-L・H・G	3	137	8	29.9	198	120+0 -0.035	172	212	175	6-M12×40L
TX85E-L・H・G	3	167	10	36.5	254	150+0 -0.040	218	258	225	6-M16×32L

Specification

Model	Torque setting range (Nm)	Spring color x number	Maximum RPM (min ^-1 )	Moment of inertia (kg ^m2 )	Product weight (kg)
TX15E-L	7～24	White × 10	900	0.78× ^10-3	1.0
TX15E-H	8～38	Red × 5
TX15E-G	13–50	Red × 10
TX20E-L	12～43	White × 12	750	1.9× ^10-3	2.0
TX20E-H	16 to 70	Red × 6
TX20E-G	40–100	Red × 12
TX30E-L	14～72	White × 12	600	5.1× ^10-3	4.0
TX30E-H	33～170	Red × 6
TX30E-G	72～200	Red × 12
TX40E-L	20 to 160	White × 12	450	1.3× ^10-3	6.5
TX40E-H	43～330	Red × 6
TX40E-G	97～400	Red × 12
TX50E-L	79～390	White × 12	400	36.6× ^10-3	12.0
TX50E-H	130～580	Red × 6
TX50E-G	280 to 800	Red × 12
TX65E-L	80～480	White × 12	300	125.5× ^10-3	25.0
TX65E-H	200–1,000	Red × 6
TX65E-G	570～1,600	Red × 12
TX85E-L	270～1,100	Yellow × 12	200	398.8× ^10-3	44.0
TX85E-H	450 to 2,100	Red × 6
TX85E-G	1,300～3,200	Red × 12

Model	Maximum shaft hole diameter (φmm)	Standard shaft hole diameter (φmm)	Pilot hole diameter (φmm)	Set screw	OverloadsShift Dimensions (mm)
TX15E-L・H・G	15	15H7×5Js9	9	2-M4	1.5
TX20E-L・H・G	20	20H7×6Js9	12	2-M4	1.9
TX30E-L・H・G	30	30H7×8Js9	19	2-M4	2.6
TX40E-L・H・G	40	40H7×12Js9	twenty four	2-M5	2.9
TX50E-L・H・G	50	50H7×14Js9	34	2-M8	3.8
TX65E-L・H・G	65	65H7×18Js9	38	2-M10	5.0
TX85E-L・H・G	85	85H7×22Js9	48	2-M12	6.0

Characteristic Curve

The torque can be changed in proportion to the number of springs. A minimum of three springs can be used.

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes TX E type Automatic reset type first appeared on Kouei Japan Trading | Get Quotation.

Suntes TXD Type Automatic Reset Type

kvtpart — Sun, 27 Dec 2020 09:52:07 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: TXD

Part Names

Hub Boss
Flanges
Action Ring
Spring
key
Steel ball
bearing
Washer
Adjustable Ring
Hexagonal Socket Set Screw
ring
WR type retaining ring
pin
Spring
Model plate
Nameplate

Size

Model	A	B	C	D	E	φF	φG	φH	φJ	Mounting bolts
Model	A	B	C	D	E	φF	φG	φH	φJ	K PCD	L Bolt size
TX15D-L/H/G	47	10	6.0	4	13.7	69	50+0 -0.025	56	96	60	6-M5
TX20D-L/H/G	53	11	8.3	4	15.1	88	65+0 -0.030	68	108	75	6-M6
TX30D-L/H/G	65	13	10.5	6	20.0	113	85+0 -0.035	84	124	100	6-M6
TX40D-L・H・G	75	15	13.2	6	20.3	134	105+0 -0.035	108	148	120	6-M8
TX50D-L/H/G	90	20	15.8	8	24.8	168	130+0 -0.040	134	174	150	6-M10

Specification

Model	Torque setting range (Nm)	Spring color x number	Maximum RPM (min ^-1 )	Moment of inertia (kg ^m2 )	Product weight (kg)
TX15D-L	7～24	White × 10	900	0.58× ^10-3	1.0
TX15D-H	8～38	Red × 5
TX15D-G	13–50	Red × 10
TX20D-L	12～43	White × 12	750	1.3× ^10-3	1.5
TX20D-H	16 to 70	Red × 6
TX20D-G	40–100	Red × 12
TX30D-L	14～72	White × 12	600	3.7× ^10-3	3.0
TX30D-H	33～170	Red × 6
TX30D-G	72～200	Red × 12
TX40D-L	20 to 160	White × 12	450	9.6× ^10-3	5.0
TX40D-H	43～330	Red × 6
TX40D-G	97～400	Red × 12
TX50D-L	79～390	White × 12	400	26.4× ^10-3	10.0
TX50D-H	130～580	Red × 6
TX50D-G	280 to 800	Red × 12

Model	Maximum shaft hole diameter (φmm)	Standard shaft hole diameter (φmm)	Pilot hole diameter (φmm)	Set screw	OverloadsShift Dimensions (mm)
TX15D-L/H/G	15	15H7×5Js	9	2-M4	1.5
TX20D-L/H/G	20	20H7×6Js9	12	2-M4	1.9
TX30D-L/H/G	30	30H7×8Js9	19	2-M4	2.6
TX40D-L・H・G	40	40H7×12Js9	twenty four	2-M5	2.9
TX50D-L/H/G	50	50H7×14Js9	34	2-M8	3.8

Characteristic Curve

The torque can be changed in proportion to the number of springs. A minimum of three springs can be used.

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes TXD Type Automatic Reset Type first appeared on Kouei Japan Trading | Get Quotation.

Suntes Type C Load Test Machine

kvtpart — Sun, 27 Dec 2020 09:23:55 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: C

Features and Applications

Features
Load testing at low rotation speeds can be easily performed.
High torque load testing can be easily performed.
Stall testing of fluid couplings is possible.
Any load torque can be set.

Applications

For:

Noise and efficiency testing of reducers
Running tests of agricultural machinery, construction machinery, etc.
Destructive testing of universal shafts
Efficiency testing of fluid couplings
Various durability tests

About the control panel

We provide standard control panels for load testing machines.
A load controller is available as an option, which corrects fluctuations in the load torque and controls it to a stable load torque.
We also manufacture specially designed measurement and control panels to meet your requirements for control and measurement functions.

Size

Model	A	B	C	φD	E	F	G	H	I	J	K	L	φd	ℓ	N-φZ
PSW-1331	1,578	1,180	515	350	145	800	600	540	600	350	40	280	90	120	6-25
PSW-1535	2,390	1,900	425	500	190	1,120	900	800	950	650	40	380	120	180	10-24
PSW-1735	2,600	2,000	450	750	240	1,370	1,200	1,070	1,150	650	40	500	140	220	10-30

Specification

Model	Maximum Absorption Power (kW)	Maximum torque (kN・m)	Maximum RPM (min ^-1 )	Cooling water volume (ℓ/min)	Maximum SettingsAir Pressure (MPa)
PSW-1331	67.5	5.7	1,500	45	0.7
PSW-1535	90	39.6	1,000	60	0.7
PSW-1735	180	66	600	120	0.7

Hydraulic servo (hydraulic control) types are also available.
If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes Type C Load Test Machine first appeared on Kouei Japan Trading | Get Quotation.

Suntes Type B Load Test Machine

kvtpart — Sun, 27 Dec 2020 09:06:43 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: B

Features and Applications

Features
Enables easy load testing at low rotational speeds.
Facilitates high-torque load testing with ease.
Allows stall testing of fluid couplings.
Supports arbitrary load torque settings.

Applications
For noise testing and efficiency testing of gear reducers.
For running tests of agricultural machinery and construction machinery.
For destructive testing of universal shafts.
For efficiency testing of fluid couplings.
For various durability tests.

About Control Panels

We provide standard control panels for load testing machines.
An optional load controller is available to correct fluctuations in load torque and ensure stable load torque control.
Additionally, we can manufacture custom-designed measurement panels and control panels tailored to your specific requirements for control and measurement functions.

Size

Model	A	B	C	φD	E	F	G	H	I	J	K	L	φd	ℓ	N-φZ
PSW-1221	1,340	940	395	270	135	680	520	450	510	300	20	230	75	120	4-24
PSW-1321	1,309	910	380	350	145	800	600	540	600	350	20	280	80	120	4-24
PSW-1525	1,880	1,450	420	500	190	1,120	900	800	950	650	30	380	120	180	6-24
PSW-1725	2,150	1,550	450	750	240	1,370	1,200	1,070	1,150	650	40	500	140	220	8-30

Specification

Model	Maximum Absorbed Power （kW）	Maximum Torque （kN・m）	Maximum Rotational Speed （min^-1）	Cooling Water Flow Rate （ℓ/min）	Maximum Set Air Pressure （MPa）
PSW-1221	30	2.7	1,800	20	0.7
PSW-1321	45	3.8	1,500	30	0.7
PSW-1525	60	26.4	1,000	40	0.7
PSW-1725	120	44	600	80	0.7

We also offer hydraulic servo (hydraulic control) types.
If you have any questions about specifications, please feel free to consult with us.
Please note that the listed dimensional specifications are subject to change without notice due to improvements.

The post Suntes Type B Load Test Machine first appeared on Kouei Japan Trading | Get Quotation.

Suntes Type A Load Test Machine

kvtpart — Sun, 27 Dec 2020 08:35:23 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: A

Features and Applications

Features
Enables easy load testing at low rotational speeds.
Allows for easy high-torque load testing.
Supports stall testing of fluid couplings.
Permits arbitrary load torque settings.

About Control Panels

We provide standard control panels for load testing machines.
As an option, a load controller is available to correct fluctuations in load torque and control it to maintain a stable load torque.
Additionally, we can manufacture custom-designed measurement panels and control panels tailored to your specific requirements regarding control functions and measurement functions.

Size

Model	A	B	C	φD	E	F	G	H	I	J	K	φd	ℓ	N-φZ
PSW-1211	632	480	430	270	35.5	725	350	300	412	270	10	50	60	4-16
PSW-1311	715	540	500	350	60	800	470	390	460	270	19	60	85	4-18
PSW-1514	1,215	800	650	500	275	1,224	580	500	702	400	42	100	150	6-23
PSW-1515	1,215	800	650	500	275	1,275	580	500	702	400	42	100	150	6-23
PSW-1715	1,580	1,000	750	755	355	1,529	1,150	1,030	1,070	650	20	140	200	8-25
PSW-1915	1,580	1,000	900	1,000	280	1,774	1,600	1,500	1,300	750	30	140	200	8-27

Specification

Model	Maximum Absorbed Power （kW）	Maximum Torque （kN・m）	Maximum Rotational Speed （min^-1）	Cooling Water Flow Rate （ℓ/min）	Maximum Set Air Pressure （MPa）
PSW-1211	15	1.35	1,800	10	0.7
PSW-1311	22	1.9	1,500	15	0.7
PSW-1514	30	8	1,000	20	0.7
PSW-1515	30	13.2	1,000	20	0.7
PSW-1715	60	22	600	40	0.7
PSW-1915	90	31	500	60	0.7

The post Suntes Type A Load Test Machine first appeared on Kouei Japan Trading | Get Quotation.

Suntes Rail clamper (long stroke type)

kvtpart — Sun, 27 Dec 2020 08:21:30 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: RC-1020L, RC-1040L, RC-1075L, RC-1120L

Model code

Long stroke type

For conventional rail clampers, the recommended range of rail side wear was 2mm.
The long stroke type is designed to maintain the specified clamping force even if the rail side wears up to 12mm (when the shoe is new).

If the rail is in the condition shown in the figure below, please repair or replace the rail so that it can be clamped.

Features

The internal unit follows the up/down and left/right undulations in the straight line direction of the rail.

It is easy to install because it is integrated with the hydraulic unit. (The hydraulic unit can also be installed separately as an option.)
Compatible with all standard rails.
Gripping force (clamping force): Maximum 1,176kN (120t) is possible.

Reliable inspection system

Before shipping, the rail clamper is inspected for runaway holding power using a holding power measuring tester.
The rail of the test device is gripped by the rail clamper, a load is applied to the rail, and it is confirmed that the rail does not move.

Size

Model	A	B	C	D	E	F	G
RC-1020L	1180	935	1180	φ26	750	55	65
RC-1040L	1220	1065	1290	φ33	830	80	95
RC-1075L	1320	1225	1450	φ39	980	85	95
RC-1120L	1500	1335	1660	φ39	1090	85	130

Specification

Model	RC-1020L	RC-1040L	RC-1075L	RC-1120L
Clamping Force(kN)	196	392	735	1,176
Friction coefficient	0.25
Runaway retention(kN)	98	196	368	588
Cylinder Size(mm)	φ105	φ145	φ190	φ230
cylinderstroke (mm)	115	116	121	132
Release operation time	Approximately 5 seconds ^*
Clamp Operation Time	Adjustable (minimum approximately 2s ^* )
Rail head width wear allowance	Can handle up to 12mm wear on various rail widths
Shoe wear allowance	1mm (one side)
Motor capacity(kW)	1.5	2.2	3.7	5.5
Tank Capacity(L)	5	5	10	10
Power supply voltage	AC200V/400V – 50Hz three-phase AC200V/220V/400V/440V – 60Hz three-phase
Power supply voltage control	AC100-110V/AC200-220V – 50/60Hz single phase
Interlock Device	Temperature switch, level switch
Hydraulic oil	Anti-wear hydraulic oil ISO VG22/VG32
Painting specifications	Undercoat: Epoxy resin paint Topcoat: Polyurethane resin paint
option	Cold region specifications, earthquake-proof specifications, special power sources, special coating, etc.

This is the value when the rail is new (no deformation or wear).
If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes Rail clamper (long stroke type) first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-0521T, DB-0522T, DB-0523T Water-cooled disk

kvtpart — Sun, 27 Dec 2020 08:08:31 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-0521T, DB-0522T, DB-0523T

Size

Model	B	t	C	D	d	F	PCD	nH	A	E	G	J	L	M.N.
DB-0521T	270	20	142	125	60	8	105	6-M10×18L	70	34	100	127	212	Rc1/2
DB-0522T	350	20	216	180	100	10	150	6-M12×20L	76	40	100	127	218	Rc1/2
DB-0533T	500	38	270	225	135	10	190	12-M16×18L	84	45	111	144	245	Rc3/4

Specification

Model	DB-0521T	DB-0522T	DB-0533T
Maximum Rotation Speed(min ^-1 )	1800	1500	1000
Moment of inertia(kg ^m2 )	0.06	0.35	1.3
Allowable energy absorption(kN・m/s)	14.7	22.0	29.4
Water volume(ℓ/min)	10	15	20
Cooling Water Pressure(MPa)	0.2	0.2	0.2
mass(kg)	13	32	53

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes DB-0521T, DB-0522T, DB-0523T Water-cooled disk first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-0511~0534H Flange Type

kvtpart — Sun, 27 Dec 2020 08:03:46 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-0511~0534H

Size

Model	D	t	B	C	d H8	F	PCD	n-φH	A	remarks
DB-0511H	260	10.4	134	124	74	9	94	4-10.5	38.2	solid
DB-0521H	270	20	140	128	60	10	86	6-10.5	44	Ventilation
DB-0522H	350	20	220	160	85	14	116	8-13	35	Ventilation
DB-0531H	382	38	–	190	108	17	142	8-15	51	Ventilation
DB-0533H	500	38	–	260	130 ^※	18	180	8-17	50	Ventilation
DB-0534H	550	38	–	260	130	18	180	8-17	50	Ventilation

Only DB-0533H is “H7”.

Specification

Model	DB-0511H	DB-0521H	DB-0522H	DB-0531H	DB-0533H	DB-0534H
Maximum Rotation Speed(min ^-1 )	2200	2200	1650	1500	1150	1050
Moment of inertia(kg ^m2 )	0.03	0.05	0.11	0.28	1.0	1.48
mass(kg)	3.8	5.3	10	18	35	43

Please contact us if you are planning to manufacture the discs yourself.
If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes DB-0511~0534H Flange Type first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-0525~0539FB-01 Flange boss type

kvtpart — Sun, 27 Dec 2020 07:57:32 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-0525~0539FB-01

Model code

Size

Model	D	t	d1		d2	d3	L	PCD	nQ
Model	D	t	Pilot hole	Max.	d2	d3	L	PCD	nQ
DB-0525FB	500	20	35	95	160	250	125	205	8-M16
DB-0526FB	600	20	35	115	190	280	145	240	10-M16
DB-0527FB	700	20	50	130	215	305	165	260	12-M16
DB-0535FB	500	38	35	95	160	250	143	205	8-M16
DB-0536FB	600	38	35	115	190	280	163	240	10-M16
DB-0537FB	700	38	50	130	215	305	183	260	12-M16
DB-0538FB	800	38	50	150	250	340	208	295	12-M16
DB-0539FB	900	38	50	170	280	380	228	330	12-M18

Specification

Model	DB- 0525FB	DB- 0526FB	DB- 0527FB	DB- 0535FB	DB- 0536FB	DB- 0537FB	DB- 0538FB	DB- 0539FB
Maximum Rotation Speed(min ^-1 )	2600	2200	1900	2600	2200	1900	1600	1450
Moment of inertia(kg ^m2 )	1.1	2.2	4.0	2.0	3.94	7.27	12.48	20.12
mass(kg)	51	75	103	76	111	152	210	276

Please contact us if you are planning to manufacture the discs yourself.
The moment of inertia and mass values are for pilot hole dimensions.
If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes DB-0525~0539FB-01 Flange boss type first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-0511~0525E-01 Boss Type

kvtpart — Sun, 27 Dec 2020 07:49:54 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-0511~0525E-01

Model code

Size

Model	D	t	B	C	d		A	L
Model	D	t	B	C	Pilot hole	Max.	A	L
DB-0511E	260	10.4	120	100	20	60	68	70
DB-0513E	350	10.4	210	110	30	60	100	110
DB-0523E	350	20	210	125	30	70	110	120
DB-0525E	500	20	360	160	35	90	130	140

Specification

Model	DB-0511E	DB-0513E	DB-0523E	DB-0525E
Maximum Rotation Speed(min ^-1 )	2200	1650	1650	1150
Moment of inertia(kg ^m2 )	0.04	0.13	0.21	0.9
mass(kg)	7.5	16	twenty three	47

The post Suntes DB-0511~0525E-01 Boss Type first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-0503E, 0504E-01 MiniDisc

kvtpart — Sun, 27 Dec 2020 07:33:01 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-0503E, 0504E-01

Model code

Dimensions

Specification

Model	DB-0503E	DB-0504E
Maximum Rotation Speed(min ^-1 )	3800	2800
Moment of inertia(kg ^m2 )	0.002	0.008
mass(kg)	1.1	2.1

The moment of inertia and mass values are for pilot hole dimensions.
If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes DB-0503E, 0504E-01 MiniDisc first appeared on Kouei Japan Trading | Get Quotation.

Suntes connector Piping parts

kvtpart — Sun, 27 Dec 2020 07:25:27 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)

Hose nipple

Dimensions

Part number	T1	A	B	C
DB-0302-01	R1/4	40	14	9.5
DB-0302-02 ^*	M16 P1.5	36	26	10

Hose attachment part: Straight shape.

Nipples

Dimensions

Part number	T1	T2	A	B
DB-0306-01	G1/8	R1/8	29	14
DB-0306-02	G1/8	DM (M10 P1.25)	32	14
DB-0306-A03	G1/8	CU (3/8-24UNF)	37.5	14
DB-0306-04	G1/8	CM (M10 P1.0)	28	14

Bushing

Dimensions

Part number	T1	T2	A	B
DB-0309-01	CU (3/8-24UNF)	Rc1/8	twenty three	14
DB-0309-A01	CU (3/8-24UNF)	Rc1/8	31	14
DB-0309-02	DM (M10 P1.25)	Rc1/8	26	14
DB-0309-04	CM (M10 P1.0)	Rc1/8	twenty three	14
DB-0309-05	M14 P1.5	DM (M10 P1.25)	29	19
DB-0309-06	R1/4	CU (3/8-24UNF)	28	19
DB-0309-07	DM (M10 P1.25)	CU (3/8-24UNF)	32	14
DB-0309-08	R1/8	CU (3/8-24UNF)	30	14

DB-0309-01 is for teacher master cylinder (DB-2204T).

Two-way connector

Dimensions

Part number	T1	T3	A	B	C	D	E	shape
DB-0300-01	DM (M10 P1.25)		35	twenty five	15	twenty five	5.5	square
DB-0300-03	Rc1/8		–	38	20	twenty two	6.5	hexagonal
DB-0300-05	CU (3/8-24UNF)	PF1/4	50	30	20	40	5.5	square

Four-way connector

Dimensions

Part number	T1	T2	T3	T4	A	B	C	D	E
DB-0305-01	DM (M10 P1.25)				35	36	15	twenty five	5.5

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes connector Piping parts first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-0113 High Pressure Hose

kvtpart — Sun, 27 Dec 2020 07:22:45 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-0113

Dimensions

L(m)	0.5	1	1.5	2	2.5	3	5	7	10	12

Specification

Hose Inner Diameter	φ3.2
Burst Pressure(MPa)	78
Maximum Operating Pressure(MPa)	19.5
Maximum operating temperature(℃)	70
Minimum bending radius(mm)	12

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes DB-0113 High Pressure Hose first appeared on Kouei Japan Trading | Get Quotation.

Suntes Copper pipe Piping parts

kvtpart — Sun, 27 Dec 2020 06:44:07 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)

Dimensions

Compatible pipe shape confirmation list

Hydraulic disc brake

DB-2051
pipeTip	doubleflare
pipenut	M10 P1.25
Model	DB-0304-01

DB-2021 (BSH)
pipeTip	Convex
pipenut	3/8-24UNF
Model	DB-0304-02

DB-2008
pipeTip	Convex
pipenut	M10 P1.0
Model	DB-0304-03

Air Booster

DB-3223 to DB-5244
pipeTip	doubleflare
pipenut	M10 P1.25
Model	DB-0304-01

Manual Booster

DB-2413 to DB-2415
pipeTip	Convex
pipenut	3/8-24UNF
Model	DB-0304-02

E-Booster

DB-4133EF to DB-4155EF
pipeTip	doubleflare
pipenut	M10 P1.25
Model	DB-0304-01

DB-4134EFT to DB-4154EFT
pipeTip	doubleflare
pipenut	3/8-24UNF
Model	DB-0304-02

Hood pedal unit

DB-2102 to DB-2107
pipeTip	doubleflare
pipenut	M10 P1.25
Model	DB-0304-01

With cushion valve
pipeTip	Convex
pipenut	3/8-24UNF
Model	DB-0304-02

With teacher master
pipeTip	doubleflare
pipenut	3/8-24UNF
Model	DB-0304-02

Specification

Model	Both ends shape	Pipe length L(m)																Pipe outer diameter/pressure resistance
DB-0104	DM-CM	0.5	1	1.5	2	2.5	3	4	5	6	7	8	9	10	12	15	20	φ4.76／15MPa
DB-0105	DM-CU
DB-0106	DM-DM
DB-0107	CU-CU
DB-0115	CU-CM
DB-0124	DU-DM
DB-0125	CU-DU

Copper pipe type selection

(Example) When connecting “DB-2021” and “DB-3223A”

“Confirmation list of suitable pipe shapes”Check the shape

Check the shape of both ends in “Specifications”

Select the required “length” from the “specifications”
The model code is “model” + “length”.If the length of “DB-0105” is “0.5”,
the model code will be “DB-0105-0.5”.

The post Suntes Copper pipe Piping parts first appeared on Kouei Japan Trading | Get Quotation.

Suntes TXB type Automatic reset type

kvtpart — Sun, 27 Dec 2020 06:35:45 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: TXB

Part Names

Hub Boss
sprocket
Action Ring
Spring
key
Steel ball
bearing
Washer
Adjustable Ring
Hexagonal Socket Set Screw
ring
WR type retaining ring
pin
Spring
Model plate
Nameplate

Size

Model	A	B	C	D	φE	φF	φG	φH
TX15B-L/H/G	47	10.6	4	13.7	80	48	56	96
TX20B-L/H/G	53	11.6	4	15.1	92	62	68	108
TX30B-L/H/G	65	12.35	6	20.0	115	77	84	124
TX40B-L/H/G	75	15.85	6	20.3	138	96	108	148

Specification

Model	Torque setting range (Nm)	Spring color x number	Maximum RPM (min ^-1 )	Moment of inertia (kg ^m2 )	Product weight (kg)
TX15B-L	7～24	White × 10	900	0.625× ^10-3	1.0
TX15B-H	8～38	Red × 5
TX15R-G	13–50	Red × 10
TX20B-L	12～43	White × 12	750	1.2× ^10-3	1.5
TX20B-H	16 to 70	Red × 6
TX20B-G	40–100	Red × 12
TX30B-L	14～72	White × 12	600	3.4× ^10-3	3.0
TX30B-H	33～170	Red × 6
TX30B-G	72～200	Red × 12
TX40B-L	20 to 160	White × 12	450	9.0× ^10-3	5.0
TX40B-H	43～330	Red × 6
TX40B-G	97～400	Red × 12

Model	Maximum shaft hole diameter (φmm)	Standard shaft hole diameter (φmm)	Pilot hole diameter (φmm)	Set screw	OverloadsShift Dimensions (mm)	sprocketNumber of teeth	sprocketPCD
TX15B-L/H/G	15	15H7×5Js9	9	2-M4	1.5	#40×18T	73.14
TX20B-L/H/G	20	20H7×6Js9	12	2-M4	1.9	#40×21T	85.21
TX30B-L/H/G	30	30H7×8Js9	19	2-M4	2.6	#50×21T	106.51
TX40B-L/H/G	40	40H7×12Js9	twenty four	2-M5	2.9	#60×21T	127.82

Characteristic Curve

The torque can be changed in proportion to the number of springs. A minimum of three springs can be used.

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes TXB type Automatic reset type first appeared on Kouei Japan Trading | Get Quotation.

Suntes NS type centrifugal brake

kvtpart — Sun, 27 Dec 2020 06:27:52 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: NS

Features

Santes NS type centrifugal brake is a mechanical centrifugal brake used to slow down the descent of elevators, water gates, and other ascending and descending equipment.
The NS type centrifugal brake has the following features.

Brake torque can be easily adjusted by changing the number of counterweights.
The speed-sensitive brake eliminates the need for a power source.
During natural descent, it automatically descends at a constant speed as designed.
You can select any brake torque.

Size

NS5-2S

NS7-2S

NS9-3S

NS9-3W

NS12-3S

NS13-3S

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes NS type centrifugal brake first appeared on Kouei Japan Trading | Get Quotation.

Suntes Centrifugal clutch NCLU type

kvtpart — Sun, 27 Dec 2020 06:24:14 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: NCLU

Size

Dimensions(mm)

Model	A	B	C	D	E	F	H	J	P	R	S	φU	mass(kg)
NCLU-136	960	430-2	90	720	1,160	550	215.5	530	300	550	600	70	350
NCLU-156	1,100	485-2	100	815	1,320	550	220.5	580	320	550	600	85	430
NCLU-186	1,200	525-2	100	915	1,420	800	232.0	620	320	600	650	95	800
NCLU-218	1,210	530-2	120	920	1,470	800	232.0	700	350	600	680	95	850
NCLU-248	1,340	390-2	160	1,010	1,680	850	255.5	780	400	680	800	125	1,150
NCLU-308	1,520	450-2	170	1,130	1,880	1,000	283.0	940	480	800	950	140	2,100

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes Centrifugal clutch NCLU type first appeared on Kouei Japan Trading | Get Quotation.

Suntes Centrifugal clutch NCL type

kvtpart — Sun, 27 Dec 2020 06:06:13 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: NCL

Structure and operating principle

Part Names

Drive shaft
Gear Clutch
Shifter lever
Centrifugal clutch
drum

Operation

1. ON
When the gear clutch is ON, the centrifugal clutch slips and gradually transmits the load as the engine speed increases. At rated speed, there is no slip and 100% power is transmitted.

2. OFF
When the gear clutch is in the OFF position, the centrifugal clutch does not transmit power even if the engine is rotating.

3. ON-OFF switching

ON/OFF switching can be easily performed by sliding the shifter lever.
Due to its structure, please do not turn the unit on or off while the engine is running.

Usage Example

When engine vertical pump is applied

When engine horizontal pump is applied

NCL type

Dimensions(mm)

Model	A	B	C	D	J	K	M	φP	φR	φS	φT	φU	φW	mass(kg)
NCL-136	853	335.5	90	200	600	280	673	30	85	143	367	70	85	145
NCL-156	1,008	421.5	127	243	600	280	673	45	115	178	414	85	95	195
NCL-186	1,105	427.5	152	286	630	320	913	65	150	230	494	95	110	290
NCL-218	1,148	470.5	152	284	630	320	913	65	150	230	576	95	110	350
NCL-248	1,330	522.0	153	331	680	320	965	70	165	254	656	125	150	520
NCL-308	1,432	614.0	203	381	740	370	1,126	75	200	305	817	140	190	890

NCL-1B type

Dimensions(mm)

Model	A	B	C	D	E	F	G	H	J	K	M
NCL1B-136	853	90	260	269.5	335.5	90	200	125	600	280	673
NCL1B-156	1,008	110	300	286.5	421.5	127	243	140	600	280	673
NCL1B-186	1,105	145	355	322.5	427.5	152	286	155	630	320	913
NCL1B-218	1,148	145	355	322.5	470.5	152	284	155	630	320	913
NCL1B-248	1,330	160	418	390.0	522.0	153	331	190	680	320	965
NCL1B-308	1,432	170	430	388.0	614.0	203	381	215	740	370	1,126

Model	φP	φR	φS	φT	φU	mass(kg)
NCL1B-136	30	85	143	367	70	205
NCL1B-156	45	115	178	414	85	255
NCL1B-186	65	150	230	494	95	350
NCL1B-218	65	150	230	576	95	425
NCL1B-248	70	165	254	656	125	600
NCL1B-308	75	200	305	817	140	970

NCL-2B type

Dimensions(mm)

Model	A	B	C	D	E	H	J	K	M	φT	φU	mass(kg)
NCL2B-136	1,303	90	260	269.5	513.5	125	600	280	673	367	70	265
NCL2B-156	1,498	110	300	286.5	611.5	140	600	280	673	414	85	315
NCL2B-186	1,690	145	355	322.5	657.5	155	630	320	913	494	95	410
NCL2B-218	1,752	145	355	322.5	719.5	155	630	320	913	576	95	495
NCL2B-248	2,075	160	418	390.0	849.0	190	680	320	965	656	125	680
NCL2B-308	2,122	170	430	388.0	874.0	215	740	370	1,126	817	140	1,050

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes Centrifugal clutch NCL type first appeared on Kouei Japan Trading | Get Quotation.

Suntes Centrifugal clutch FA type Basic type centrifugal clutch

kvtpart — Sun, 27 Dec 2020 04:48:00 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: FA

Size

Dimensions(mm)

Model	A	B	C	D	G	H	I	J	K	L	M
FA-53	130	9	14	107	77.0	8.0	45	161	70	35	15
FA-73	186	9	57	120	119.0	17.0	50	213	85	50	20
FA-93	220	11	60	149	129.0	26.0	65	270	130	70	20
FA-123	277	13	69	200	165.5	26.5	90	340	143	80	30
FA-136	282	15	67	200	165.5	26.5	90	367	143	85	30

When manufacturing a flywheel adapter, please let us know the detailed dimensions of the flywheel.
If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes Centrifugal clutch FA type Basic type centrifugal clutch first appeared on Kouei Japan Trading | Get Quotation.

Suntes Centrifugal clutch type C Basic type centrifugal clutch

kvtpart — Sun, 27 Dec 2020 04:39:51 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: C

Structure and operating principle

Part Names

Boss mounting bolt
Hub Boss
Set screw
Shoe Support
U Nut
Drum flange
Drum Rim
Spring washer
Hexagonal bolt
U Nut
Link plate
Copper rivets
Clutch lining
Shoe
sleeve
Rubber bushing
Shoe mounting bolt

Operation

When the drive is stopped, the drum and driving unit are not in contact, so no power is transmitted. When the driver’s rotation speed begins to increase, the shoe is pressed against the drum by centrifugal force, transmitting power to the driven unit while slipping. When the driver’s rotation speed reaches the rated speed, slippage disappears and 100% power is transmitted.

Size

Dimensions(mm)

Model	A	B	C	D	E	F	G	H	J	K	L	M	N
C-53①	38	45	10	161	15	35	60	15	35	80	107	27	70
C-73①	54	50	7	213	20	50	85	20	50	88	120	32	85
C-93①	67	65	7	270	20	70	115	twenty five	70	102	149	47	130
C-123②	89	90	7	340	40	80	135	30	80	130	200	70	143
C-136②	100	90	6	367	40	85	160	30	85	130	200	70	143
C-156③	115	127	6	414	45	115	146	45	115	148	248	94	178
C-186③	150	152	8	494	65	127	196	64	150	176	310	110	230
C-218③	152	152	7	576	70	150	210	64	150	172	311	112	230
C-248③	172	153	6	656	70	165	235	70	165	238	331	93	254
C-308③	203	203	13	817	70	175	288	75	200	248	419	133	305
C-368③	254	254	12	984	100	200	292	100	200	283	520	184	350
C-4510③	254	280	12	1,245	100	225	405	100	225	318	546	228	349

Specification

Model	Unit standard shaftHole Diameter	Engagement speed(rpm)			Product weight(kg)
Model	Unit standard shaftHole Diameter	L shoe	H shoe	G shoe	unit	drum
C-53	35φH7	1,240	990	740	1.97	4.5
C-73	45φH7	1,120	900	610	5.27	9.1
C-93	55φH7	900	720	520	9.46	18.0
C-123	65φH7	780	590	–	18.54	28.5
C-136	80φH7	660	380	–	28.58	32.5
C-156	–	620	450	370	46.56	54.7
C-186	–	460	330	280	82.4	87.0
C-218	–	420	300	240	92.3	116.0
C-248	–	350	270	220	156.9	158.4
C-308	–	240	170	160	291.0	287.6
C-368	–	240	190	–	322.0	667.0
C-4510	–	160	120	100	640.0	1,090.0

53~123 MAX Set, 136~4,510 MID Set.
We have a high engagement type available for idling operation. Please contact us for more information.
If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes Centrifugal clutch type C Basic type centrifugal clutch first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-2173 Hand Lever Unit

kvtpart — Sun, 27 Dec 2020 04:25:51 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-2173

Model code

Dimensions

Specification

Model	DB-2173	DB-2173D
Master cylinderModel	DB-2203M	DB-2203MD
Hydraulic oil	Brake fluid (DOT3 equivalent) orMineral oil (equivalent to ISO VG32)
Discharged oil volume( ^cm3 )	5
Tank hose length(m)	–	5
mass(kg)	5.9	6.4

Generated hydraulic pressure

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes DB-2173 Hand Lever Unit first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-2183, 2184, 2185 Combination Unit

kvtpart — Sun, 27 Dec 2020 04:07:18 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-2183, 2184, 2185

Model code

Size

Model	A	B	C	D	E	F	G	H	I	J
DB-2183	417	320	290	80	55	161	400	301	271	3
DB-2183D	417	320	290	80	55	161	400	301	271	3
DB-2184D	462	360	330	84	60	175	406	312	291	3
DB-2184E	462	360	330	84	60	175	406	312	291	3
DB-2185D	544	365	335	110	80	162	392	322	346	4
DB-2185E	544	365	335	110	80	162	392	322	346	4

Specification

Model	DB-2183	DB-2183D	DB-2184D	DB-2184E	DB-2185D	DB-2185E
Master cylinderModel	DB-2203M	DB-2203MD	DB-2204MD	DB-2204ME	DB-2205MD	DB-2205ME
Hydraulic oil	Brake fluid (DOT3 equivalent) or mineral oil (ISO VG32 equivalent) ^*
Discharged oil volume( ^cm3 )	5		6.9		12
Tank hose length(m)	–	5	10	–	10	–
mass(kg)	7.4	8.4	9.5	8.9	12.5	11.9

DB-2184 type is brake fluid (DOT3 equivalent) only.

Generated hydraulic pressure

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes DB-2183, 2184, 2185 Combination Unit first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-2123, 2104, 2105, 2106, 2107 Foot pedal unit

kvtpart — Sun, 27 Dec 2020 03:58:56 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-2123, 2104, 2105, 2106, 2107

Model code

Size

Model	A	B	C	D	E	F	G	H	I
DB-2123/DB-2123C	354	320	290	80	55	141	246	193	3
DB-2104/DB-2104C	382	300	270	95	65	168	315	262	4
DB-2105/DB-2105C	464	300	270	95	65	168	379	326	4
DB-2106・DB-2106C DB-2107・DB-2107C	471	300	270	95	65	168	379	326	4

Specification

Model	DB- 2123	DB- 2123C	DB- 2104	DB- 2104C	DB- 2105	DB- 2105C	DB- 2106	DB- 2106C	DB- 2107	DB- 2107C
Master cylinderModel	DB- 2203M	DB- 2203MC	DB- 2204M	DB- 2204MC	DB- 2205M	DB- 2205MC	DB- 2206M	DB- 2206MC	DB- 2207M	DB- 2207MC
Hydraulic oil	Brake fluid (DOT3 equivalent) or mineral oil (ISO VG32 equivalent) ^*
Discharged oil volume( ^cm3 )	5		6.9		12		19.4		28
Tank hose length(m)	–	5	–	10	–	10	–	10	–	10
mass(kg)	6.6	7.0	8.4	8.8	9.3	9.7	10.6	11.0	10.6	11.0

DB-2104, 2107 are brake fluid (DOT3 equivalent) only.

Generated hydraulic pressure

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes DB-2123, 2104, 2105, 2106, 2107 Foot pedal unit first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-2102,2103 Foot pedal unit

kvtpart — Sun, 27 Dec 2020 03:49:38 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-2102,2103

Model code

Size

Model	A	B	C	D	E	F	G
DB-2102	380	265	235	75	50	162	140
DB-2102C	380	265	235	75	50	130	140
DB-2103	450	265	235	75	50	162	175
DB-2103C	450	265	235	75	50	130	175

Specification

Model	DB-2102	DB-2102C	DB-2103	DB-2103C
Master cylinderModel	DB-2203M	DB-2203MC	DB-2203M	DB-2203MC
Hydraulic oil	Brake fluid (DOT3 equivalent) or mineral oil (ISO VG32 equivalent)
Discharged oil volume( ^cm3 )	5
Tank hose length(m)	–	5	–	5
mass(kg)	4.6	5.0	4.8	5.2

Generated hydraulic pressure

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes DB-2102,2103 Foot pedal unit first appeared on Kouei Japan Trading | Get Quotation.

Suntes Design and sales of hydraulic units

kvtpart — Sun, 27 Dec 2020 03:39:10 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)

Recruitment record

ElevatorWinding machine	Motor 0.75kW, Maximum pressure 13.7MPa,Discharge rate 1.2L/min, tank capacity 20L
Container craneElevation device	Motor 0.75kW, Maximum pressure 14.0MPa,Discharge rate 1.5L/min, tank capacity 30L
Ladle CraneMain Volume	Motor 3.7kW, Maximum pressure 16.7MPa,Discharge rate 9.4L/min, tank capacity 100L

Hydraulic circuit reference diagram

Oil tank
Fuel filler and air fillerBreather
Oil level gauge
Ball valve
SuctionStrainer
Solenoid valve
Manifold
Manual pump
Ball valve
Pressure Switch
Pressure
Terminal box
Coupling
Electric motor
Gear Pump

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes Design and sales of hydraulic units first appeared on Kouei Japan Trading | Get Quotation.

Suntes Power box (AP-2403) For E-booster/electromagnetic brake

kvtpart — Sun, 27 Dec 2020 03:35:35 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: AP-2403

Dimensions

Block Diagram

Specification

Power supply voltage(V)	AC180-240 50/60Hz
Output voltage during suction(V)	DC150～210
Output voltage when held(V)	DC20-30
Maximum current(A)	17 (Connect two DB-415*(When suctioning with AC240V power supply voltage)
Rating	1800 times/h
Thread Size	Main terminal block: M4 ALARM terminal block: M3
Applicable models	All E-booster models: DB-41EF, DB-41EFT All electromagnetic brake models: DB-40**EF
mass(kg)	4.0

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes Power box (AP-2403) For E-booster/electromagnetic brake first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-4154EFT Spring actuated electromagnetic release type

kvtpart — Sun, 27 Dec 2020 03:29:18 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-4154EFT

Model code

Dimensions

Common to all EBoosters: 600mm cable length with relay connector included

Specification

Master cylinderModel	DB-2204TS-01
Hydraulic oil	Brake fluid (DOT3 equivalent)
Discharged oil volume( ^cm3 )	6
Supply suction voltage(V)	DC150～210
Supply Holding Voltage(V)	DC20～31
Power Consumption(W)	37 (continuously held at DC31V)
Rating	360 cycles/h 50% ED,Or maintain continuous current
Required power capacity(VA)	3253
Applicable power supply box	AP-2403
mass(kg)	53.5

Generated hydraulic pressure

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes DB-4154EFT Spring actuated electromagnetic release type first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-4144EFT Spring Actuated Electromagnetic Release Type

kvtpart — Sun, 27 Dec 2020 03:24:12 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-4144EFT

Dimension

Specification

Master cylinderModel	DB-2204TS-01
Hydraulic oil	Brake fluid (DOT3 equivalent)
Discharged oil volume( ^cm3 )	4.8
Supply suction voltage(V)	DC150～210
Supply Holding Voltage(V)	DC20～31
Power Consumption(W)	22 (Continuously held at DC31V)
Rating	360 cycles/h 50% ED,Or maintain continuous current
Required power capacity(VA)	1912
Applicable power supply box	AP-2403
mass(kg)	33

The post Suntes DB-4144EFT Spring Actuated Electromagnetic Release Type first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-4134EFT Spring actuated electromagnetic release type

kvtpart — Sun, 27 Dec 2020 03:04:31 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-4134EFT

Model code

Dimensions

Common to all EBoosters: 600mm cable length with relay connector included

Specification

Master cylinderModel	DB-2204TS-01
Hydraulic oil	Brake fluid (DOT3 equivalent)
Discharged oil volume( ^cm3 )	3
Supply suction voltage(V)	DC150～210
Supply Holding Voltage(V)	DC20～31
Power Consumption(W)	17 (continuously held at DC31V)
Rating	360 cycles/h 50% ED,Or maintain continuous current
Required power capacity(VA)	1495
Applicable power supply box	AP-2403
mass(kg)	15.5

Generated hydraulic pressure

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes DB-4134EFT Spring actuated electromagnetic release type first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-4155EF Spring actuated electromagnetic release type

kvtpart — Sun, 27 Dec 2020 02:59:28 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-4155EF

Model code

Dimensions

Common to all EBoosters: 600mm cable length with relay connector included

Specification

Master cylinderModel	DB-2205MS-01
Hydraulic oil	Brake fluid (DOT3 equivalent)
Discharged oil volume( ^cm3 )	12
Supply suction voltage(V)	DC150～210
Supply Holding Voltage(V)	DC20～31
Power Consumption(W)	37 (continuously held at DC31V)
Rating	360 cycles/h 50% ED,Or maintain continuous current
Required power capacity(VA)	3253
Applicable power supply box	AP-2403
mass(kg)	52

Generated hydraulic pressure

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes DB-4155EF Spring actuated electromagnetic release type first appeared on Kouei Japan Trading | Get Quotation.

Suntes DB-4154EF Spring actuated electromagnetic release type

kvtpart — Sun, 27 Dec 2020 02:51:12 +0000

Manufacture: Suntes (Sanyo Shoji Co., Ltd.)
Model: DB-4154EF

Model code

Dimensions

Common to all EBoosters: 600mm cable length with relay connector included

Specification

Master cylinderModel	DB-2204MS-01
Hydraulic oil	Brake fluid (DOT3 equivalent)
Discharged oil volume( ^cm3 )	6
Supply suction voltage(V)	DC150～210
Supply Holding Voltage(V)	DC20～31
Power Consumption(W)	37 (continuously held at DC31V)
Rating	360 cycles/h 50% ED,Or maintain continuous current
Required power capacity(VA)	3253
Applicable power supply box	AP-2403
mass(kg)	53.5

Generated hydraulic pressure

If you have any questions about specifications, please contact us.
The dimensions and specifications listed may be changed without notice for improvement purposes.

The post Suntes DB-4154EF Spring actuated electromagnetic release type first appeared on Kouei Japan Trading | Get Quotation.