Features

The CY and CYW series are slit-type nozzles design specifically for high-pressure air (compressors, etc.).
They deliver a stable linear air flow from low to high air speeds, ensuring consistent removal during air blowing processes such as drying and dewatering on production lines.
While the jet slit specifications are the same as the DY and DYW series of compressor slit-type nozzles , this series features an air inlet located in the center of the back.
Multiple inlets can install on the same surface.
While the standard model features a single inlet in the center of the back, adding multiple inlets reduces inlet resistance and allows for a stronger linear air flow.

Specifications

Features

The CX series is a slit-type air nozzle designed specifically for use with high-pressure air (compressors, etc.).
It can deliver a stable linear air flow from low to supersonic speeds, making it ideal for air blowing processes such as drying and draining on production lines.
While the jet slit specifications are the same as those of the DX series of slit-type air nozzles for compressors , the CX series has the air inlet attached to the center of the back.
This CX series is suitable for situations where the inlet needs to be located in the same position due to piping arrangements, or when particularly strong air velocity is required for air blowing, such as instant draining and rapid drying.

Specifications

Features

Features

This is an electric air heater designed to achieve high heat exchange efficiency. In this series, a single heater can support two branches, and it also includes a blower heater (patent 3051625) that can be used for this purpose

Specifications

Specifications

• Body Casing: SUS304
• Exhaust Pipe: SUS321
• Equipped with Overheat Protection
• Power: 3-phase, 200V
• Maximum Operating Temperature: 280°C
• Maximum Intake Air Temperature: 100°C
• Body Pressure: 30 Kpa

The performance data is at 20°C.

The pressure loss characteristics are based on the model used for the connection diameter shown below:

ST-3A, ST-4A → φ65

ST-3B, ST-4B → φ65

ST-5, ST-6 → φ75

Specifications

Features

The soft urethane fluid injection outlet protruding from the back of the cover rotates at high speed, causing intermittent shock waves to spread over a wide area.
Compared to the pushing effect of conventional air guns, the Pata Gun’s air hitting effect reduces air consumption and shortens processing time.

1. The air outlet of the nozzle tube behind the cover rotates at high speed.
2. By rotating, intermittent shock waves spread over a wide area.
3. It can remove water and dust more effectively than conventional air guns.
4. By rotating the nozzle tube outlet, processing time can be shortened and air consumption can be reduced without changing the flow rate

Specifications

Features

This series is mainly used for rapid drying, instant heating, and similar processes in conveyor lines. It uses both spray-type and suction-type designs. The nozzle is installed in pairs as shown in the diagram.

The RCP and RCI series are designed based on our company’s unique expertise and rich experience. With a robust spray and suction power, the system flows hot air strongly in both the conveyor direction and reverse. By positioning it as shown in the diagram, efficient drying and heating are achieved

Specifications

Features

The stability of drying and heating temperature is improved, enabling effective surface treatment, resin processing, tree resin solidification, solidification, cooling, and handling of light-weight materials through specialize internal structures.
These structures help produce even airflow. Additionally, when using heat adjustment systems, the airflow is combine with heat diffusing techniques, ensuring consistent temperature throughout

B Series

• The nozzle is effective for areas with narrow gaps or irregular indentations on surfaces. Compared to slit-type nozzles, it generates stronger airflow at the center of the holes and can blow air over larger distances, as the surrounding air swirl is lessened.

T Series

• Even when used at high temperatures, the slit remains stable. It is also optimal for applications where the nozzle’s output is restricted.

Features

Multi-Branch Type Blanch Heater
A single heater can support 2 to 10 branches!!
The heater capacities range from 3 KW to 28 KW

Specifications

Features

This is a multipurpose electric heater for generating hot air, designed to achieve a high heat exchange rate. It is a stainless steel heater, but mass production has made it possible to achieve a low price.
With a wide range of models available, you can freely select and connect them, and they have a long life and can operate continuously.

Specifications 

The hot air heater SH series has stainless steel gas contact parts, so it can also be used for steam heating.

Features

The soft urethane fluid injection outlet protruding from the back of the cover rotates at high speed, causing intermittent shock waves to spread over a wide area. Compared to the pushing effect of conventional air guns, the Pata Gun’s air hitting effect reduces air consumption and shortens processing time.

1. The air outlet of the nozzle tube behind the cover rotates at high speed.
2. By rotating, intermittent shock waves spread over a wide area.
3. It can remove water and dust more effectively than conventional air guns.
4. By rotating the nozzle tube outlet, processing time can be shortened and air consumption can be reduced without changing the flow rate.

Specifications

Features

The EX and EX series nozzles are developed for cutting plates, used in drying lines, and designed for processing both edges of the workpiece

Specifications

Features

This is a dry-type nozzle designed for cutting corners of vertical components. As shown in the diagram, it is used near the corner and exhibits excellent performance on the two surfaces where the corner and air come into contact.

The previous method of water cutting and dry cutting had difficulties processing the edges of workpieces with a multi-angle cross-section.
This nozzle resolves these issues and is effective in cooling and dispersing the air on surfaces outside the corner

Specifications

Features

The JX and JN series ring nozzles were developed mainly for internal water cutting and drying of cylindrical workpieces such as pipes and tubes

Specifications

Features

Previous models had a multiple-hole structure arranged on the circumference, with short holes and slits. In high-speed water cutting and drying operations, problems such as processing burrs occurred.
The RX-RN series, designed with uniform holes on the circumference, sprays air from specific gaps, allowing burr-free processing

Specifications

Features

With the development of the BOW nozzle, nozzles are arranged in ideal positions as shown in the diagram for surface processing of flat materials (films, metal plates, paper, printing press, etc.) such as water cutting, drying, and heating.
The previous model (P2-8 references) allows easy combination of nozzles in the configuration shown in the diagram

Specifications

Features

This unit is designed to combine two nozzles in a way that is suitable for the appropriate angle depending on the line speed.
It is used in high-speed lines for cutting wires, tubes, threads, and rods, where it provides excellent power for drying. The nozzle system shown below is designed for this purpose

Specifications

Features

The surface processing of flat materials (steel plates, paper rolls, etc.) in drying lines primarily uses slit-type air knives.
In these cases, the air sprayed onto the workpiece spreads evenly along the surface and flows toward the center, which sometimes causes an issue of uneven processing at both ends of the piece.
The EX and EN nozzle types can be installed at both ends in conjunction with slit-type nozzles, solving this problem

Specifications

Features

This is a dry-type nozzle for cutting corners of vertical components. It is used as shown in the diagram below, where it is used near the corner and performs excellently on both the two surfaces where the corner and air come into contact.

The previous method of water cutting and dry cutting had difficulties with processing the edges of workpieces with a multi-angle cross-section.

With this nozzle, it is possible to handle these areas. The nozzle is effective in cooling and dispersing the air, which is directed to the area outside the corner and helps to treat a wider range

Specifications

Features

• The JX series is a nozzle designed for high-pressure air (compressors).
• The JN series is a nozzle designed for high-pressure blower air. It demonstrates stable performance at wind speeds from low to 160 m/s.
• These nozzles can be connected to heat air generators and used with high-temperature air.
• Custom sizes larger or smaller than the standard diameters are also available

Specifications

Features

Previous models had a multiple-hole structure arranged on the circumference, with short holes and slits. In high-speed and dry cutting operations, problems like processing burrs occurred.
The RX-RN series is design with a uniform distribution of holes on the circumference, allowing air to be sprayed from the gaps, enabling burr-free processing.

• The RX series is a nozzle design for high-pressure air (compressors)

• The RN series is a nozzle design for high-pressure blower air. It demonstrates stable performance at wind speeds from low to 160 m/s.

• These nozzles can connect to heat air generators and used with high-temperature air.

• We also manufacture custom sizes with diameters larger or smaller than the standard size

Specifications

Features

This series has undergone full-scale model changes to significantly improve performance.
The heater uses Ti-added carbon graphite stabilized wires, which further enhance durability.
Additionally, the development of specialized internal flow structures allows for both miniaturization and low-pressure optimization.
The dedicated fixing screws and brackets are designed to make installation simple.

Specifications

Features

This series offers standard models with a maximum heat resistance of 200°C, and models up to 500°C are also available. As the heater is cartridge-type, it is easy to replace or change the heater capacity by simply using a wrench.
The main body material is SUS304 stainless steel, and the heat-resistant material uses nickel chrome or kanthal wire, which provides high heat resistance due to its special internal design, offering excellent durability for high-temperature use.

Specifications

Features

It can be used in a variety of fields that require a high level of cleanliness, such as draining and dust removal from various glass plates for LCDs and PDPs, nozzles for heating devices that spray hot air, semiconductor manufacturing equipment, and food production lines.
It can be completely disassembled, so acid washing and electrolytic polishing (passivation treatment) can be performed reliably to every corner of the interior.
The results of chemical polishing and cleaning can be visually confirmed, ensuring a high level of cleanliness.

Specifications

Features

It can use in a variety of fields that require a high level of cleanliness, such as draining and dust removal from various glass plates for LCDs and PDPs, nozzles for heating devices that spray hot air, semiconductor manufacturing equipment, and food production lines
It can completely disassemble so acid washing and electrolytic polishing (passivation treatment) can performe liably to every corner of the interior.
The results of chemical polishing and cleaning can be visually confirmed, ensuring a high level of cleanliness.

Specifications

Features

The processing equipment and device sections are design to connect with a workpiece for use in areas where this nozzle is intend to use
The nozzle has high atomization effectiveness and excellent stability, making it ideal for low-speed liquid and gas formation.
The tip of the lip is carefully engineer to prevent spray irregularities by using a specific angle of edge processing

Specifications

Features

This nozzle has an internal deformed V-shaped flow plate that allows it to produce flat air with low pressure loss even without an adjustment function, ensuring stable performance from low to high wind speeds.

Specifications

Features

The internal specifications of the nozzle for the KT series are determined according to the application and other conditions. Please feel free to consult us when selecting a nozzle.
When using a long nozzle with a strong wind speed, we recommend providing multiple nozzle inlets to reduce pressure loss in the piping.
Multi-hole and suction types are also available as custom orders.

Specifications

Features

The DLX & DLXW series are slit-type nozzles for air blowing exclusively for high-pressure blowers.
They ensure a stable linear air flow from low to high air speeds, allowing for even removal during air blowing processes such as drying and draining on the line.
The CL & CLW series for high-pressure blowers and the CLX & CLXW series for high-pressure blowers have the same jet slit specifications, but this series minimizes installation space by attaching the air inlet to the end.

Specifications

Features

The DL series is a slit-type nozzle for air blowing exclusively for high-pressure blowers.
It ensures a stable linear air flow from low to high air speeds, allowing for even removal during air blowing processes such as drying and draining on the line.
The jet slit specifications are the same as those of the CL & CLW series for high-pressure blowers , but this series has an air inlet attached to the end.

Specifications

Features

The DM series is a slit-type nozzle for air blowing exclusively for high-pressure blowers.
It ensures a stable linear air flow from low to high air speeds, allowing for even removal during air blowing processes such as drying and draining on the line.
The jet slit specifications are the same as those of the CM & CMW series for high-pressure blowers , but the DM series minimizes installation space by attaching the air inlet to the end.

Specifications

Features

The DN series is a slit-type nozzle for air blowing exclusively for high-pressure blowers.
It ensures a stable linear air flow from low to high air speeds, allowing for even removal during air blowing processes such as drying and draining on the line.
The specifications of the jet slit are the same as those of the CN series for high-pressure blowers , but the DN series minimizes installation space by attaching the air inlet to the end.

Specifications

Features

The CLX & CLXW series are slit-type nozzles for air blowing designed specifically for high-pressure blowers.
They deliver a stable linear airflow from low to high air speeds, ensuring consistent removal during air blowing processes such as drying and dewatering on production lines.
While the jet slit specifications are the same as the DLX & DLXW series for high-pressure blowers , this series features an air inlet located in the center of the back.
Multiple inlets can also be installed on the same surface. While the standard model features a single inlet in the center of the back, adding multiple inlets reduces inlet resistance and allows for a stronger linear airflow.
This series is ideal for situations where multiple inlets are required in the same location due to piping arrangements, or when particularly strong airflow is required for instant dewatering or rapid drying.

Specifications

Features

The CL & CLW series are slit-type nozzles for air blowing designed specifically for high-pressure blowers.
They deliver a stable linear airflow from low to high air speeds, ensuring consistent removal during air blowing processes such as drying and dewatering on production lines.
While the jet slit specifications are the same as those of the DL series for high-pressure blowers and the DLX & DLXW series for high-pressure blowers , this series features an air inlet located in the center of the back.
Multiple inlets can also be installed on the same surface. While the standard model features a single inlet in the center of the back, adding multiple inlets reduces inlet resistance and allows for a stronger linear airflow.
This series is ideal for situations where multiple inlets are required in the same location due to piping arrangements, or when particularly strong airflow is required for instant dewatering or rapid drying.

Specifications

Features

The CM&CMW series are slit-type nozzles for air blowing designed specifically for high-pressure blowers.
They ensure a stable linear air flow from low to high air speeds, ensuring consistent removal during air blowing processes such as drying and draining on production lines.
While the jet slit specifications are the same as those of the DM series for high-pressure blowers , this series features an air inlet located in the center of the back.
Multiple inlets can also be installed on the same surface.
While the standard model has a single inlet located in the center of the back, adding multiple inlets reduces inlet resistance and allows for a stronger linear air jet.
This series is suitable for situations where multiple inlets are required in the same position due to piping arrangements, or when particularly strong airflow is required for instant draining or rapid drying.

Specifications

Features

Air is blown in from one end of the nozzle body, and the long slit type DLZ series for compressors produces a linear, flat air stream thanks to its special internal structure.
The ultra-fine slits allow for powerful air injection with minimal air consumption, and the discharged air is uniform, eliminating unevenness and contributing to energy savings.

Specifications

Features

Air is blown in from one end of the nozzle body, and the long slit type DZ series for compressors produces a linear, flat air stream thanks to its special internal structure.
The ultra-fine slits allow for powerful air injection with minimal air consumption, and the discharged air is uniform, eliminating unevenness and contributing to energy savings.

Specifications

Features

The DY&DYW series for compressors is a slit-type nozzle for air blowing exclusively for high-pressure air (compressors, etc.).
It ensures a stable linear air flow from low to high air speeds, allowing for even removal during air blowing processes such as drying and draining on the line.
The specifications of the jet slit are the same as those of the CY&CYW series nozzles for compressors , but the DY&DYW series for compressors has an air inlet attached to the end.
A standard bracket is also available for the DY&DYW series for compressors. (Made to order, sold separately)

Specifications

Features

The DX series is a slit-type nozzle for air blowing exclusively for high-pressure air (compressors, etc.).
It ensures stable linear air flow from low to high air speeds, allowing for even removal during air blowing processes such as drying and draining on the line.
The specifications of the jet slit are the same as those of the CX series compressor nozzle and the CY & CYW series compressor nozzle , but the DX series has an air inlet attached to the end.

Specifications