Aluminum Ferrule (JIS/EN)

Mandrel Seamless Tube, Double Type

JIS H4080 (According to JIS B8817)

Mandrel Seamless Tube, Single Type

JIS

JIS H4080 (According to JIS B8817)

You can correct your curls and perform maintenance and inspection at the same time! Easily straighten thick wires with maximum output of 3TON

“R-30” is a hydraulic wire rope straightening machine with a maximum output of 3TON that can straighten thick wires easily.
Maintenance and inspection can be performed at the same time as straightening the rope, increasing the safety of the sling rope.
Since it can be operated with a foot switch, both hands can be used freely in any working position.
Also, you can make corrective strokes as you wish.
The hydraulic pump is 100V/0.4kW, and the machine dimensions are only W400 x D570 x H950mm.
It is very easy to move and select a work location.

Senyo’s 4S Function

• Safety《SAFETY》
  You can perform maintenance and inspection at the same time as straightening the rope, increasing the safety of the sling rope.
• Strong 《STRONG》
  Hydraulic type with maximum output of 3TON. Even thick wires can be straightened easily.
• Speed ​​《SPEED-UP》
  Can be operated with a foot switch, so both hands can be used freely at any work position. Also, the corrective stroke can be done as desired.
• Small 《SMALL》
  Hydraulic pump is 100V-0.4kW, the mechanical dimensions are only 400 x 570 x 950H, and the weight is 100kg. It is very easy to move and select a work location.

*All production capabilities are based on JIS6×24.

Speedy and sharp cutting! It is a cutter with a good blade.

“PCE-13SV / PCE-20SV” is an electro-hydraulic wire rope cutter.

A cutter that is fast, sharp, and has a long blade.
It has a fast cutting speed and high efficiency, and can easily cut chains and piano wire.

• PC wire and hard steel wire cutter
• Easy to separate due to its light weight
• One-touch operation

PC Cutter PCH-13 / PCH-20 [Manual Hydraulic Type]

Wire rope cutter used exclusively for PC wire and piano wire

“PCH-13 / PCH-20” is a manual hydraulic wire rope cutter.
This cutter is exclusively for PC wire and piano wire, and is widely used in that industry.

Most cable sizes are OK with this one unit! Compact design allows installation without taking up space

The “SWD-90K” is a hydraulic electric wire and cable cutter that can cut cables up to φ90mm in diameter and is compatible with most cable sizes.

The two blades on the left and right sides cut the hairs with scissors. Unlike a rotary blade, it produces almost no dust.
It can cut hairs in bulk, which greatly improves work efficiency.

Since it is hydraulic and has a compact design, it can be installed in your current workplace without taking up space.

Chain Cutter PCE-25 Type

Cut with scissors! No sparks, chips or dust! Improved work efficiency compared to a grindstone cutter

The “PCE-25 model″ is an electro-hydraulic chain cutter that uses a hydraulic system to make it more compact .
It has a simple structure consisting of a hydraulic system and a cutter head, and by adjusting the length of the hydraulic cable that connects the two , it can be customized to suit your work site. In addition, you can work even more efficiently by customizing the cutter head with a trigger switch .

• Cutting through chains with hydraulic power
• Can cut wire up to 25mm in diameter
• Achieved compactness

SKS-28 [Electromechanical]

An open rotary cutter that saves you the hassle of cutting! Manage the number of cuts with the counting function

“SKS-28″ is an electro-mechanical wire rope cutter.
Since it is an opening type rotary cutter, cutting is not a hassle.
Furthermore, it has a counting function that allows you to manage the number of cuts, and the crank mechanism allows you to cut quickly at a constant cutting speed.

Equipped with casters for easy movement.

*All cutting capacities are based on JIS 6×24.

Wave Dragon E-60 / L-100 [Manual Hydraulic Type]

Lightweight, safe and economical! A wire rope cutting machine that can easily cut thick and hard ropes.

“Wave Dragon E-60 / L-100″ is a manual and lightweight wire rope cutting machine.
We have a wide range of well-known models that are synonymous with wire rope cutters around the world and have been recognized for their ease of use and sharpness, and have been exported in large numbers .
No auxiliary tools are required for the job, and beautiful cuts can be made in just a few seconds. The cutting blade can be easily polished and replaced.

• Lightweight, safe and economical
• Easily cuts thick and hard ropes

* The E type comes with a separate trolley, and the L type comes with a rubber wheel swivel trolley.
*All cutting capacities are based on JIS6×24.

Wave Dragon A-20 / B-30 / C-40 / D-50 [Manual Hydraulic Type]

Lightweight, safe and economical! A wire rope cutting machine that can easily cut thick and hard ropes.

“Wave Dragon A-20 / B-30 / C-40 / D-50″ is a manual hydraulic type lightweight wire rope cutting machine.

We have a wide range of well-known models that are synonymous with wire rope cutters around the world and have been recognized for their ease of use and sharpness, and have been exported in large numbers .

No auxiliary tools are required for the job, and beautiful cuts can be made in just a few seconds.
The cutting blade can be easily polished and replaced.

• Lightweight, safe and economical
• Easily cuts thick and hard ropes

*All cutting capacities are based on JIS6×24.

Electro-hydraulic Type

An open rotary cutter that saves you the hassle of cutting! Light and compact, easy to move

“SWDR-24 / SWDR-32″ is an electro-hydraulic wire rope cutter.

Since it is an opening type rotary cutter, cutting is not a hassle.
It has a lightweight and compact design and comes with casters for easy movement.
Furthermore, it has a counting function that allows you to manage the number of cuts.

*All cutting capacities are based on JIS6×24.

Easy to move with casters! Efficient wire rope cutter with fast cutting speed

The “SWD-40S/60S/100S/120S” is an electric hydraulic wire rope cutter suitable for cutting wire rope .

Moreover, the cut surface is extremely beautiful and does not damage the wire, and it is easy to operate, making it suitable for cutting before lock processing.

• Improved work efficiency as it is mobile (with wheels)
• Easy to operate with manual switching valve type.
• Cuts large diameter wire rope quickly and efficiently.

*All cutting capacities are based on JIS6×24.

Easy to move with casters! Efficient wire rope cutter with fast cutting speed

Hydraulic wire rope cutter ideal for cutting wire rope.

Moreover, the cut surface is extremely beautiful and does not damage the wire, and it is easy to operate and has no danger at all, making it ideal for cutting before lock processing.

• Lightweight mobile type (with casters)
• Cutting speed is fast and efficient.
• The structure has been revised compared to the previous model, and failures have been drastically reduced.
• Easy to operate with manual switching valve type.

*All cutting capacities are based on JIS6×24.

Clamp tube made of special material suitable for use in high temperature atmospheres and chemicals.

Please be sure to use this product when using stainless steel rope.
(W) We offer size variations from 1.5mm to 36mm.

• Applicable range: In high temperature atmosphere, in chemicals

A clamp tube that seals the end of the rope without reducing the strength of the crimped part.
The clamp tube is thinner and longer than the W clamp tube. And its shape after crimping is smaller in diameter and smarter than the W type. The cross section of the clamp tube is almost similar to the W tube.

The W type requires that the end of the rope protrude slightly even after crimping. But the WN type requires that the end of the rope protrude slightly even after crimping. But the WN type requires that the end of the rope not reduce the strength of the crimped part. So that the sling operator will not be injured by the protruding part of the rope. This is a new type that can be adapted to the PL law era with a clamp tube designed to seal the area.

• Thin long size

WN Clamp Pipe Lock Processing Method

• Fold back the end of the rope to make an eye and set the clamp tube under the neck of the eye.
• Align the rope end with the end of the clamp tube.
• Crimp with the specified pressure, being careful not to pull the end of the rope into the clamp tube.
• Remove any protruding burrs with a burr cut, etc.

Clamp tube that generates little burrs and requires almost no effort in post-processing.
“Senyo Aluminum W Clamp Tube” is a product with an oval outer diameter and a cocoon-shaped inner diameter.

• Insert two wire loafs in parallel into the clamp tube.
• The contact area between the wire rope and the tube becomes very large.
• The excess material is pushed outward and is completely tightened.
• Fewer burrs occur and post-processing requires almost no effort.
• No loss of clamp tube

W Clamp Pipe Lock Processing Method

• Fold back the end of the rope to make an eye and set the clamp tube under the neck of the eye.
• Leave the rope end extending beyond the end of the Klumph tube by the rope diameter.
• Perform crimping at specified pressure.
• Remove any protruding burrs with a burr cut, etc.

Beautiful finish! Stationary burr cutter that can significantly reduce deburring time
“SBC-2” is a stationary burr cutter suitable for cutting protruding burrs on the clamp part after locking aluminum pipes.

• Ideal for cutting burrs protruding from the clamp part after locking aluminum pipes.
• Significantly reduces deburring work time.
• Beautiful finish.
• No clogging of grindstones, discs, etc.
• Does not damage the wire rope.
• Particularly effective for non-ferrous metals.
• Dust does not scatter.

* All production capabilities are based on JIS6×24.

Clamp pipe temporary tightening machine When setting the clamp pipe of thick rope, it can be securely fixed.
“SP-38/SP-56/SP-100” is a set press that can securely fix thick ropes in a clamp tube temporary tightening machine.
The lineup includes “SP-38” with a maximum working capacity of 38 mm (W), “SP-56” and “SP-100”.

• Working capacity: max. (W) 56mm
• High pressure hose: 3m included
• Body weight: 16.5kg
• Pump weight: 30kg
• 0.4kW・100V

* All production capabilities are based on JIS6×24.

A new type of triangular vise that uses a vertical claw from the middle of the horizontal claw to pull in the rope and create an eye.
“DV-42-II/DV-70-II/DV-100-II” is a triangular vise that opens and closes the horizontal jaws and pushes and pulls the vertical jaws.

• Vertical claw from the middle of the horizontal claw
• A new method of pulling in the rope and creating an eye
• We can also process hard ropes.
• This is a labor-saving decision type.

* All production capabilities are based on JIS6×24.

A new type of triangular vise that uses a vertical claw from the middle of the horizontal claw to pull in the rope and create an eye.

“DV-42-II/DV-70-II/DV-100-II” is a triangular vise that opens and closes the horizontal jaws and pushes and pulls the vertical jaws.

• The opening and closing of the horizontal claws and the pushing and pulling of the vertical claws are all electrically operated.
• Vertical claw from the middle of the horizontal claw
• A new method of pulling in the rope and creating an eye
• We can also process hard ropes.
• This is a labor-saving decision type.

* All production capabilities are based on JIS6×24.

A triangular vise that allows for easy course machining, regardless of lock machining or satsuma machining.
“HV-42/HV-70” is a manual triangular vise that allows you to easily create eyes with rope diameters that are impossible to do manually.

• Doesn’t require a lot of force.
• Work quickly
• Course insertion is especially convenient.

* All production capabilities are based on JIS6×24.

You can easily perform coarse machining, whether it involves lock machining or Satsuma machining.
DV-42/DV-70 is a triangular vise with a foot switch that allows you to freely open and close the side claws.

• The HV is labor-saving.
• You can open and close the side claws simply by pressing the foot switch.
• You can also set the press SP-56.

* All production capabilities are based on JIS6×24.

SZ-150. Trust in “closing power”. Senyo extruder.
“SZ-150” is a machine specialized for wire rope end processing.

• You can easily, quickly, and neatly perform flat end processing.
• The equipment comes with casters for easy movement.

*Manufacturing capacity is based on our extruded sleeves, and wire ropes are based on JIS standards.

HST-2

• Ideal for caulking ultra-fine wire rope.
• Light and compact, you can use it anywhere.

Manual Hydraulic Pump Specifications

Manual Hydraulic Press Machine Specifications

LH-16 [Portable Manual Type]

Easy to process even for inexperienced people! Sling wire ropes can be manufactured on-site for ships.
“LH-16” is a wire rope lock processing machine that can produce wire rope for slinging in the forest, on ships, etc.

• Inexperienced workers can easily process it with a manual output of 500KN (50TON).
• You can easily check the pressure, ensuring a constant fastening force.

PCL-25D/PCL-25H /PCL-25H customized version [Portable manual type / desk type machine for ultra-fine objects]

PCL-25D [Desk Type Machine For Ultra-fine Objects]

Easy to operate, labor-saving, highly efficient, and multi-capable! A special machine that can efficiently caulk odd-shaped terminal fittings.
“PCL-25D” is a desk-type wire rope lock processing machine exclusively for ultra-fine materials.

• For extra-fine ropes
• Cylindrical
• Ball shape
• Square
• Hexagon
• In addition, oddly shaped terminal fittings can be caulked efficiently.

PCL-25H [Portable Manual Type]

Easy to operate, labor-saving, highly efficient, and multi-capable! Portable manual wire rope lock processing machine
“PCL-25H” is a portable wire rope lock processing machine with an output of 250KN (25TON).

• No power source is required as pressure is applied manually.
• You can process the terminals of thin items on-site.
• Easy to use even for inexperienced users.
• By checking the pressure gauge and operating the handle, uniform products can be produced.

PCL-25H [Customized Version]

It can be customized to suit various scenes.

*Manufacturing capacity is based on the use of aluminum tubes and wire ropes based on JIS 6×24.

Since it is digital, you can set any pressure at once! Desk type lock processing machine
“SLD-120C” is a desk-type wire rope lock processing machine equipped with a spacious workbench.

• Desk type with a spacious workbench
• Inching and automatic work with a single touch of a foot switch
• Even women can perform safe, labor-saving, and highly efficient work
• Pressure setting is digital and can be set to any pressure at once.

*Manufacturing capacity is based on the use of aluminum tubes and wire ropes based on JIS 6×24.

Easily process various end fittings with hooks! C-type press machine with high efficiency and excellent workability

The “C-170/C-310/C-500” is a wire rope lock processing machine that can easily process various end fittings with rings and hooks.

• The wide front opening allows for easy and highly efficient work.
• You can easily process various end fittings with rings and hooks.
• You can digitally set the pressure to any desired level at once.
• Loading and unloading horizontally reduces conventional processing steps.

*Manufacturing capacity is based on the use of aluminum tubes and wire ropes based on JIS 6×24.

Demonstrating High Functionality in Swaging Process of Cable End Fittings! A New Model Integrating Only the Advantages of Traditional Types
The “D-1000/1200/1500/2000/3000/4000/5000” is a wire rope swaging machine that demonstrates high functionality in the swaging process of cable end fittings.

• Pressure Settings are Digital: Allows for instant setting to the desired pressure.
• Gate-Type Frame with Cut-Out Plate Welding: No welded parts.
• Increased Frame Cross-Sectional Area: Pursuing high rigidity.
• Minimized Frame Front and Rear Dimensions: Improved workability.
• Guide Inside the Frame for Up-and-Down Movement of Dies: Prevents die wobbling.
• Easy Attachment and Detachment of Cylinders: Facilitates labor-saving repairs

*Manufacturing capacity is based on the use of aluminum tubes and wire ropes based on JIS 6×24.

D-310

D-500 / D-700

Anyone can easily process wire ropes such as sling ropes and wire rope springs!
Automatic pressure display and selection of material and rope type are possible through panel operation.

The D series is a new model that brings together only the advantages of the conventional model.
Highly functional for crimping cable end fittings.
In addition, pressure settings are automatic and the setting screen is a touch panel, making it easy for anyone to use.
We pursue high rigidity by increasing the cross-sectional area of ​​the frame, and further reduce the front and rear dimensions of the frame to the utmost, achieving improved workability.

• Displays pressure during pressing
• Smaller and lighter
• Secure a large work space and increase work efficiency
• Gate-shaped frame for hollowing out thick plates and welding: No welded parts
• The die moves up and down with the guide inside the frame: Prevents the die from swinging.
• Easy to attach and detach the cylinder: Save labor for repairs

Select from driving modes

Select material and rope type

Calculate pressure automatically

Also displays pressure during pressing

*Manufacturing capacity is based on the use of aluminum tubes and wire ropes based on JIS 6×24.

Easy to work with, even beginners can use it! Simple type wire rope lock processing machine

“D-170” is a simple type wire rope lock processing machine that operates pressure – neutral – return using a lever.
In addition, it is easy to work with, so even beginners can use it.

• Simple type
• Pressure setting is digital and can be set to any pressure at once.

*Manufacturing capacity is based on the use of aluminum tubes and wire ropes based on JIS 6×24.