A0-503H Hex-S Set S (Dog Point (HOEI))
Model: A0-503H
dia range:M3～M6
Length range:3～10
Iron (or standard).
Plain, Trivalent zinc cr+3 color white, Trivalent zinc cr+3 color black, Nickel, Chrome.
| Nominal Diameter (d) | M3 | M4 | M5 | M6 | M8 | M1 0 | M 1 2 | Mt 6 | ||
| Pitch (P) | 0.5 | 0.7 | 0.8 | 1.0 | 1.25 | 1.5 | 1.75 | 2.0 | ||
| dp | Max | 2.0 | 2.5 | 3.5 | 4.0 | 5.5 | 7.0 | 8.5 | 12.0 | |
| Min | 1.75 | 2.25 | 3.2 | 3.7 | 5.2 | 6.64 | 8.14 | 11.57 | ||
| df | Approximate | Minor Diameter of External Thread | ||||||||
| e | Min | 1.73 | 2.30 | 2.87 | 3.44 | 4.58 | 5.72 | 6.86 | 9.15 | |
| S | Nominal | 1.5 | 2.0 | 2.5 | 3.0 | 4.0 | 5.0 | 6.0 | 8.0 | |
| Min | 1.520 | 2.020 | 2.520 | 3.020 | 4.020 | 5.020 | 6.020 | 8.025 | ||
| Max | 1.545 | 2.045 | 2.560 | 3.071 | 4.084 | 5.084 | 6.095 | 8.115 | ||
| t | Min (3) | 1Column | 1.2 | 1.5 | 2.0 | 2.0 | 3.0 | 4.0 | 4.8 | 6.4 |
| 2Column | 2.0 | 2.5 | 3.0 | 3.5 | 5.0 | 6.0 | 8.0 | 10.0 | ||
| z | Short tip (3) | MIn | 0.75 | 1.0 | 1.25 | 1.5 | 1.0 | 2.5 | 3.0 | 4.0 |
| Max | 1.0 | 125 | 1.5 | 1.75 | 2.25 | 1.75 | 3.25 | 4.3 | ||
| Long tip (3) | Min | 1.5 | 2.0 | 2.5 | 3.0 | 4.0 | 5.0 | 6.0 | 8.0 | |
| Max | 1.75 | 2.25 | 2.75 | 3.25 | 4.3 | 5.3 | 6.3 | 8.36 | ||
| ℓ | ||||||||||
| Dimensions based on nominal length | Min | Max | ||||||||
| 4 | 3.76 | 4.24 | 4 | |||||||
| 9 | 4.76 | 5.24 | 5 | 5 | ||||||
| 6 | 5.76 | 6.24 | 6 | 6 | 6 | |||||
| 8 | 7.71 | 8.29 | 8 | 8 | 8 | 8 | 8 | |||
| 10 | 9.71 | 10.29 | 10 | 10 | 10 | 10 | 10 | 10 | ||
| 12 | 11.65 | 12.35 | 12 | 12 | 12 | 12 | 12 | 12 | j 12 | |
| 16 | 15.65 | 16.35 | 16 | 16 | 16 | 16 | 16 | 16 | 16 | 16 |
| 20 | 19.58 | 20.42 | 20 | 20 | 20 | 20 | 20 | 20 | 20 | 20 |
| 25 | 24.58 | 25.42 | 25 | 25 | 25 | 25 | 25 | 25 | 25 | 25 |
| 30 | 29.58 | 30.42 | 30 | 30 | 30 | 30 | 30 | 30 | 30 | 30 |
Note (1): If the total length (ℓ) applied to (a) is shorter than the dotted line shown in the table below, a 120° chamfer is applied. If it is longer, a 90° chamfer is applied.
Note (2): The 45° angle applies to the sloped area below the minor diameter of the external thread.
Note (3):
If the “minimum t” in Row 1 and the “short tip” z value are shorter than the reference point for the applied length (ℓ), it is applied.
If the “minimum t” in Row 2 and the “long tip” z value are longer, it is applied as well.
REQUEST QUOTATION
PAYMENT
LINK
