Drilling and Cutting, Japan, Unika
UNIKA PE-400G (Cartridge Type) Resin A
Manufacturer: UNIKA
Model: PE type (Resin cartridge), PE type exclusive parts, Installation specifications, Push pump, Metal brush, Extension nozzle(including three)
- ■Can be used for various bolts, sizes and shapes of different shape reinforced steels.
- ■Excellent in chemical resistance, and can be used for installation in water.
- ■Demonstrates stable fixing strength because primary material and hardening agent are constantly mixed by mixing nozzle.
- ■Adopts high performance epoxy resin with no resin contraction. Also less odor and toxicity.
Uses
Concrete•Rock bed
- Drill vertically to target surface with the determined preparation diameter and preparation hole depth.
- Use a dust collector or blower to thoroughly remove chips in the hole.
- Remove chips adhered in the hole using a brush, and use a dust collector or blower to clean in the hole again.
- Insert the nozzle down to the hole bottom and fill resin.
- Insert the bolt down to the hole bottom while slowly turning it by hand.
- Do not move the anchor bolt within the determined hardening time after embedding.
■Uses
Foundation work for iron frame, Passage construction work, Tunnel construction work, Installation for vibrating machines.
■Structural Drawing
■Installation specifications
| Nominal diameter(mm) |
M8 | M10 | M12 | M16 | M20 | M22 | M24 |
|---|---|---|---|---|---|---|---|
| Preparation hole diameter(mm) |
10.0 | 12.0 | 14.0 | 18.0 | 24.0 | 25.0 | 28.0 |
| Embedment depth(mm) |
80 | 90 | 110 | 130 | 170 | 190 | 210 |
| Required resin amount(ml) |
4 | 6 | 9 | 15 | 42 | 43 | 66 |
| Recommended tightening torque(Nm) |
10 | 20 | 40 | 80 | 120 | 140 | 160 |
| Number of pieces installed(Pcs.) |
87 | 58 | 38 | 23 | 8 | 8 | 5 |
*Number of pieces installed is for reference number of pieces at a loss rate of 20%.
■Shape of bolt used
Cannot be used for a round bar. Use bolts which have irregularity on a surface such as a continuous thread bolt and different shape bar steel.
■Guideline for hardening time
| Temperature(℃) | 5 | 15 | 25 | 35 | 40 |
|---|---|---|---|---|---|
| Use time(minutes) | 100 | 60 | 40 | 25 | 20 |
| Hardening time(minutes) | 2400 | 1440 | 660 | 540 | 480 |
(Do not move the anchor reinforcement within the hardening time.)
- Avoid direct sunlight and store in a well-ventilated place where the temperature does not rise so high.
(Never raise the temperature above 40℃. Always keep the temperature in the range of 5 to 25℃.) - Do not bring close to fire or high temperature objects.
- Cartridge can be stored until the expiration date for use under standard storage conditions.
- Wear protective equipment (such as protective glasses and mask) when using.
- When resin adheres to skin, irritation may occur in rare cases. Take action such as immediately wiping and rinsing with a hot soapy solution.
In addition, if resin gets into eyes, immediately rinse with a large amount of water and seek medical attention.
- Make sure to provide the drilling diameter and drilling depth as described in the specifications.
- Make sure to use both a metallic brush and blower to sufficiently clean inside the hole.
- Make sure to mount the mixing nozzle with it just before use.
- Make sure to discard first approximately 20~30cc at a time of first use and nozzle replacement. (Mixing improperly may result in reduction in strength.)
- This cannot be used for a steel bar with no irregularity such as a round bar.
- Refer to the scale on the cartridge label for discharge resin amount.
- Do not move the bar steel nor apply load within the determined hardening time.
- SPECIFICATIONS
- PE type (Resin cartridge)
-
Size Capacity(ml) PE-400G 400 
- PE type exclusive parts
-
Product name Size Matching cartridge Mixing nozzle(2 Pcs.) RA-MX2PEGN PE-G Injection gun 400 RA-GUN400 PE-400G 
- Installation specifications
-
Use bolt different shape reinforced steel Preparation hole diameter(mm) M8 10 M10 12 D10 13 M12 14 D13 16 M16 18 D16 20 M20 24 D19 25 M22 25 D22 28 M24 28 D25 32 M30 35 D29 38 
-
■Related items
- Push pump
-
Size Specifications RA-PUP (Nozzle diameter) 10mm (Hose length) 270mm 
- Metal brush
-
Size Specifications RA-MB10 Φ10*300 RA-MB13 Φ13*300 RA-MB18 Φ18*300 RA-MB28 Φ28*300 
- Extension nozzle(including three)
-
Size Specification RA-EXP3 Φ8×1m 
Related Products
-
TONE 3TX-T Torx Socket (Heavy Duty)
-
Hammer Caster 426G-C Cast Iron
-
Eagle Clamp UGHA Type Clamp for U-shaped Groove / Groove Lid / Clamp for Curb
-
HANKOKU MG-0000WP-TINF Siren Control Panel
-
LOBTEX DSX-SF STLOCK Standard Socket (High Durability Type）
-
Kimoto Instrumentation Other slopes and sprayed materials
REQUEST QUOTATION
PAYMENT
LINK
