TOYO KEIKI JGP Series Temperature Transducer

Product Made In Japan
Manufacturer: Toyo Keiki
Model: JGP Series

JGP－□: As a temperature sensor the thermocouple is a temperature-DC conversion device.
Generous input specifications. ・Covers the seven types of sensor, ranging from 0～1700℃,regulated by JIS C 1602-1995(thermocouples).
Photo couple provides complete insulation between input and output-the influence of common mode noise is excluded and stable operation is ensured(AC 2000V,1 min.).
Linearizer is standard. ・Linearity below±0.3%.
Cold junction compensation(standard junction compensation) is standard ambient temperature range－10℃ to ＋55℃
Equipped with a burnout function circuit failure is immediately detected and output.
Plug-in type makes upkeep and configuration changes simple.

Specification

INPUT	OUTPUT	AUXILIARY POWER SUPPLY
Three types of B, R, S, K, E, J, T, N thermocouples conforming to JIS C 1602-1995. Six bands of measurement temperature range are standard. Cold junction compensation built-in.	8 standard type of output are available. Burnout: Upper	AC 100/110V ±10% 50/60HZ approx. 3 VA AC 200/220V ±10% 50/60Hz approx. 3 VA DC 24V ±10% approx. 3 W DC 100/110V ±10% approx. 3 W DC 48V (38-62V) approx. 3 W Types are immediately available. For types not listed above contact a company representative.
Available types of thermocouple Thermocouples based on JIS C 1602-1995 standards Corresponding to B, R, S, K(CA), E(CRC), J(IC), T(CC). For special temperature measurement ranges, please contact a company representative and explain your needs.	Available with Max. voltage output 10V (600Ω~∞) Max. current output 20mA (0-550Ω) The burnout value may be lowered according to your needs.

Connection Diagram

JGP Series

Specified Character

(1) Available types of thermocouple
B, R, S, K(CA), E(CRC), J(IC), T(CC), N thermocouples conforming to on
JIS C 1602-1995(letters in brackets refer to former JIS designations).
(2) Tolerance
±0.5% of output span. (Ambient temperature 23℃)
(3) Effect of temperature
Within ±0.2% of output span. (For 23℃±10℃ variations)
(4) Effect of auxiliary power supply
Within ±0.1% of output span. (For rated voltage ±10% variations)
(5) Effect of load resistance
Within ±0.05% of output span. (For load resistance range)
(6) Output ripple
Within 0.5%p-p of output span.
(7) Response time
Shorter than 0.5sec. (Time to 99% output)
(8) Dielectric strength
2000V AC,1min. (50／60Hz)
(Between input,output,auxiliary power supply and external case)
(9) Insulation resistance
Higher than 100MΩ at 500V megger.
(Between input,output,auxiliary power supply and external case)
(10) Built-in Functions
Isolation(photo-couple method)-standard
Linearizer(linearity within±0.3%)-standard
Burnuot function – In the standard specification burnout is set for when the following upper limit
is exceeded:when the output value=max.output value＋10～15% of the output span(e.g.,21.6～
22.4mA when the output is 4～20mA).
The burnout value may be lowered according to your needs.
(11) Attachment
Temperature detection device for Cold junction compensation
Type : ZGP－A1
(12) Weight
Approx.410g

AVAILABLE WORKING RANGE

SENSOR TYPE	AVAILABLE WORKING RANGE	MIN. TEMP. RANGE OF AVAILABLE TYPES
B	300℃ ～ 1820℃	1000℃
R	−50℃ ～ 1760℃	1000℃
S	−50℃ ～ 1760℃	1000℃
K(CA)	−270℃ ～ 1370℃	100℃
E(CRC)	−270℃ ～ 1000℃	100℃
J(IC)	−270℃ ～ 1200℃	100℃
T(CC)	−270℃ ～ 400℃	100℃
N	−270℃ ～ 1300℃	200℃

DESIGNATION ITEM AT ORDER

1. TYPE AND AUXILIARY POWER SUPPLY	2. INPUT	3. OUTPUT
JGP－□	－□ □□	－□

	AUXILIARY POWER SUPPLY
1	DC 24V
2	AC 100V/110V 50/60HZ
3	AC 200V/220V 50/60Hz

5	DC 100V/110V
6	DC 48V


9	OTHER

MARK	TEP.SENSOR	MARK	INPUT
1	K(CA)	1	0 ~ 100°C
2	E(CRC)	2	0 ~ 200°C
3	J(IC)	3	0 ~ 300°C
4	T	4	0 ~ 400°C
5	R	5	0 ~ 500°C
6	B	6	0 ~ 800°C
7	S	7	0 ~ 1000°C
8	N	8	0 ~ 1200°C
9	OTHER	9	OTHER

OUTPUT	LOAD RESIS.
DC 0 ～ 100mV	600Ω ～ ∞
DC 0 ～ 1 V	600Ω ～ ∞
DC 0 ～ 5 V	600Ω ～ ∞
DC 0 ～ 10 V	600Ω ～ ∞
DC 1 ～ 5 V	600Ω ～ ∞
DC 0 ～ 1mA	0 ～ 10kΩ
DC 0 ～ 10mA	0 ～ 1kΩ
DC 4 ～ 20mA	0 ～ 550Ω
OTHER OUTPUT