Fushiman P100-3X Pressure Reducing Valves With Integral By-Pass

Manufacturer: Fushiman Co.,LTD.
Model: P100-3X

Model	Nominal Diameter	Primary Pressure	Secondary Side Setting Range	Maximum Operating Temperature	Body Material	Connection
P100-3X	20～100	MAX. 1.0MPa	0.03～0.7MPa	90℃	CAC	Flange, Threaded

(External appearance for nominal diameters of 50 or below)

No need for bypass piping.
For nominal diameters 20 to 50, switching between pressure reduction, shutoff, and bypass can be done with a wrench.
(For nominal diameters 65 to 100, a manual handle is provided.)
The pressure-reducing mechanism can be disassembled and inspected while water is flowing.
Pressure gauge mounting tap holes are provided on both inlet and outlet sides.
Greatly reduces pipeline design and construction work.
Significantly minimizes the installation space required for the pressure-reducing valve.
Made of CAC and SUS materials, eliminating concerns about corrosion.
Low-profile design makes it ideal for indoor installation.
Strainer is built-in.

Specifications and Materials

Fluid	Nominal Diameter	Pressure (MPa)		Temperature (°C)	Main Component Materials				Pipe Connection
Fluid	Nominal Diameter	Primary Side	Secondary Side Setting Range	Temperature (°C)	Valve Body & Switching Valve	Valve Diaphragm	Valve Seat	Valve Stem	Pipe Connection
Water, Hot Water	20-25	0.08 – 1.0	0.03 – 0.15 0.1 – 0.7	0 – 90	Bronze	Synthetic Rubber	Bronze	Bronze or Stainless Steel	JIS Rc Threaded Connection
Water, Hot Water	32-100	0.08 – 1.0	0.03 – 0.15 0.1 – 0.7	0 – 90	Bronze	Synthetic Rubber	Bronze	Bronze or Stainless Steel	JIS 10K Full-Face Flange

Nominal Diameter	Minimum Set Differential Pressure (MPa)	Minimum Adjustable Flow Rate (L/min)	Valve Capacity		Offset (MPa)		Shutoff Pressure Rise (MPa)	Valve Seat Leakage
			Cv Value	Maximum Flow Rate (L/min)	Set Pressure Range
			Cv Value	Maximum Flow Rate (L/min)	0.03 – 0.15	0.1 – 0.7
20	0.05	0.5	2.6	55	≤ 0.05	≤ 0.07	≤ 0.02	≤ 0.01% of Rated Flow
25		0.5	3.9	85
32		2	6.3	120
40			8.3	150
50			13	250
65		5	21	350	≤ 0.07	≤ 0.07
80			26	450
100			40	700

Under conditions where the primary-side pressure is 0.6 MPa and the set pressure is 0.2 MPa, the measured background noise level is 30 dB(A) at a measurement distance of 15 cm.
The noise level may differ under conditions where the primary-side pressure is 0.6 MPa but the set pressure is different from 0.2 MPa.

Nominal Diameter 20・25	Nominal Diameter 32–50

(mm, kg)

Nominal Diameter	D (Thread Size)	L (Length)		H1	H2	E	Mass (kg)
Nominal Diameter	D (Thread Size)	Threaded Type	Flange Type JIS 10K	H1	H2	E	Mass (kg)
20	3/4	160		126	165	100	6.5
25	1	160		126	165	100	6.5
32			200	130	235	130	13.5
40			200	130	235	130	14
50			220	140	275	145	19
65			270	201	315	190	41
80			270	201	315	190	42
100			330	215	373	215	58

For nominal diameters 65 to 100, a manual handle is attached, and the shape differs partially from the diagram.

The pressure gauge mounting hole is Rc 3/8 for nominal diameters up to 100.

Use a tool (monkey wrench of 250 mm or larger) to rotate the lower shaft, allowing switching between:
- Pressure reduction mode
- Shutoff mode
- Bypass mode
After switching, be sure to tighten the hex nut to lock it securely.