, , ,

Line Seiki MDR Series Electronic Preset Counter

Product Made in Japan
Manufacturer: Line Seiki
Model: MDR Series

MDR Series Electronic Preset Counter

Model

ModelsDigitsPreset LevelPreset DigitsPreset RangeMemoryOptionWeight
MDR-144M4141 – 9999OBCD
Output
950 g
MDR-166M661 – 999999
MDR-244M4241 – 99991050 g
MDR-266M661 – 999999

Description

The MDR (Preset) Series is a 4 or 6 digits, Single or Dual level bi-directional preset counter in a DIN 72 x 144 panel size (Panel Cut-out size: 68 x 140mm).  It has a RED LED display with a digit figure size of 14.22 x 8.13mm.  This is a very simple counter but highly reliable.  This counter has a high count speed of 5kHz maximum and can accept Contact or Non-Contact pulse input. The counter offers two modes: Add/Subtract or Quadrature. It comes with a built-in contact relay and an NPN Open collector. When the counter hits the preset value, this setup sends out an output signal. Preset value can easily be set via the front panel digital switches and there are LED indicators that show the state of the unit.  The MDR (Preset) Series allows you to choose between two power sources: AC100/110V or AC200/220V. Additionally, it provides an external power supply of DC12V specifically for sensors. When it comes to resetting the unit, you have the option to do it remotely or through an auto-reset function. Memory is also available for count value retention even during power loss.

Specification

ModelsMDR-144MMDR-166MMDR-244MMDR-266M
DisplayRed LED, 14.22 x 8.13mm (Zero Suppress)
Input Method /
Signal
Contact Input: Relay, Microswitch

Non-Contact Input : L: 0 – 1V ; H: +4.5 – 27

Count Mode90°Quadrature (directional) / Add/Subtract
Count SpeedContact Input : 20 Hz max. / Non-Contact Input : 5000 Hz max.
Pulse WidthContact Input : 25 msec min. / Non-Contact Input : 100 msec min.
Make (Duty)1 : 1
Output TypeContact output : Relay Type 1C (AC230V, 2.5A max. load) * for each output

Non-contact output : NPN open collector (DC30V, 100mA maximum)

Output DisplayTurns ON during output time
Output TimeOne-shot mode: 0.1 – 3sec (adjustable)

Overrun mode: Infinite

Preset Level 1: Infinite

Preset Level 2: Infinite or 0.1 – 3sec (adjustable)

ResetRemote reset (100msec min.)

Auto-reset : One-shot reset (Output relay : 0.1 – 3sec reset)

MemoryE²PROM (10 years. retention, 10,000 times)
Power Source for SensorDC12V 100mA maximum
Input Impedance5kΩ
Power SourceAC100/110V or AC200/220V ±10%, 50/60 Hz
Power ConsumptionApproximately 5.5VA
Operating Temperature0 – 40°C (non-freezing)
Operating Humidity45 – 85%RH (non-condensing)
Hi-pot TestAC1500V (1minute)
Dielectric Test20MΩ min. (DC500V megger)
ConnectionM3 Terminal Screw

Rear Terminals and Wiring

NOTE:

  • For 1 level preset models (MDR-144M and MDR-166M), refer to Output 2 in the diagram as the main output.
  • Both terminals 12 and 13 are GND. The terminal 13 can be used in replacement of terminal 12 as described in the connection diagrams below.

Connection

Caution

  1. Avoid sending a voltage signal to the Contact Input and Remote Reset terminals to prevent internal damage.
  2. Choose either Contact or Non-contact input; you can’t use both at the same time.
  3. If there’s a power failure, the LED display turns off, and the counter won’t recognize inputs or resets.
  4. Connect terminals 11 and 12 to activate the memory feature. If you’re turning off the counter for a while, disconnect these terminals to save the internal battery, which charges when the counter is powered on.
  5. You can’t input signals to both Add and Subtract inputs at the same time.
  6. For the Input and Reset terminals, use shielded leadwires. Also, keep power source lines away from Input and Reset lines for optimal performance.

Operating Mode

Application

Product Counting

Counters can be used for counting, sorting and packaging various products.

Cut-to-length operation

Counters and CT1/CS pulse generators can be used for cut-to-length operation for textiles, paper, plastic films and so on.

Length Measuring

Counters and rotary encoders can be used for measuring the length of textiles, paper, plastic film and so on.


Other items of Line Seiki

Request the quotation for Line Seiki

REQUEST QUOTATION

PAYMENT

payment-methods

Return Top