Japan, Magnescale
Magnescale LH72 Digital Readout
Made in Japan
Manufacturer: Magnescale Co., Ltd.
Model: LH72
Features
- Counter for Lathe (LH72-3)
- Display Resolution Switching
- Machine error compensation
- Data Storage
- Reset/Preset
- Detecting Reference Point of Measurement Unit
- Program function
- Scaling
- Lathe function (Tool coordinating / Adding function)
Specifications
| Specifications | |||
|---|---|---|---|
| Model | LH72 | ||
| Display | 7 digits and minus display | ||
| Connectable measuring unit | GB-ER, PL20C (Direct) / DG-B (Necessary to use the conversion adaptor which is sold separately) | ||
| Measuring unit input resolution | Standard: 0.1 μm, 0.5 μm, 1 μm, 5 μm, 10 μm, 1 s, 10 s, 1 min, 10 min Expanded: 100 μm, 50 μm, 25 μm, 20 μm, 2 μm, 0.05 μm, 1 degree can be added | ||
| Display resolution | Measuring unit input resolution or higher and diameter display (except for angle display) | ||
| Input signal | A/B quadrature, Z phase (Conforms to EIA-422) | ||
| Minimum input phase difference | 100 ns | ||
| Quantization error | ±1 count | ||
| AlarmDisplay | Measuring unit disconnected, Excess speed, Maximum display amount exceeded, Power failure, Error in stored data | ||
| Reset | Resettable by key switch | ||
| Preset | It is possible to store/call 3 kinds of numbers. | ||
| Reference point detection | The reference point of the measuring unit can be detected | ||
| Data storage | The value displayed before the power was turned off and setting values are stored | ||
| Linear compensation | A fixed compensation amount is applied to the measuring unit’s count value. Compensation amount Standard: ±600 μm/m (Expanded: ±1000 μm/m) | ||
| Segmented error compensation | The movement range of the measuring unit with a reference point can be divided into amaximum of 32 sections, and error compensation is performed for each of these sections. Compensation amount: ±600 um (at each section) | ||
| Scaling | Scaling factor:0.100000 ～ 9.999999 | ||
| Program |
|
||
| Angle display | Can be displayed as an angle value when the Digiruler is pasted to the arc surface | ||
| Sleep | The display is turned off when no operations are made for a preset time. (The time can set.) | ||
| Display | 2-axis display (2-axis or 3-axis input) | ||
| Tool offset | 99 | ||
| Measuring unit input addition2 | 2-axis addition display is available | ||
| Display hold | The displayed value can be held and the tool coordinate entered. | ||
| Power supply | DC 12 V Rating 0.75 A Max. 1 A AC 100 V to 240 V ±10 % When using the AC adaptor PSC-22 (For U.S. only) or PSC-23 (For Europe and other countries) *Option | ||
| Power consumption | max.32 VA (connected at the AC adaptor.) | ||
| Operating temperature | 0 ～ 40°C (non condensing) | ||
| Storage temperature | -20 ～ 60°C (non condensing) | ||
| Mass | Approx. 1.5 kg | ||
Related Products
-
Shimizu MK Scaling Chisel – Tip Tool
-
Eagle Jack (Konno Corporation) ED-40-PG-75kM-40 Hydraulic Bottle Jack
-
TOKU Sinker Rock Drill
-
TSUBOSAN BRHI-EX12 235mm/150mm ENGINEER’S FILES 150mm SIZE BRIGHT-900 SINGLE BASTARD / SINGLE SECOND EXTREME
-
Gentos AX-P1R Wide Beam Bike Light (750lm / 7400cd)
-
TONE BTIP12S Torx Plus Bit Set
REQUEST QUOTATION
PAYMENT
LINK
