,

Tokyo Ko-on Denpa LSVH Series Manual Control Fader

Made in Japan
Manufacturer: Tokyo Ko-on Denpa Co., Ltd.
Model: LSVH Series

Features

Direct print resistor element used (Special surface treatment).
Horizontal style control-bar design (Protection against dust).
PCB Terminal style.

LSVH Series

Electrical Specifications (Initial Value)

Electrical specifications (initial value) LSVH Series
Products LSVH-****-B* 2LSVH-****-B* LSVH-****-* 2LSVH-****-*
Number of circuits / Type of output laws 1
Linear taper
2
Linear taper x2
1
Audio taper
2
Audio taper x2
Circuit method Potentiometer circuit Ladder circuit
Total resistance (1-3) 10kohm, 5kohm
Total resistance tolerance ±20%
Absolute linearity ±5%
(The travel is divided into 10 sections and 11 positions are measured.)
Residual voltage (1-2), (2-3) 20mV or less
Residual resistance (1-2), (2-3) 50ohm or less
Attenuation accuracy [Load: high] 0 – 20dB: ±3.0dB
Matching accuracy 0 – 20dB: 3.0dB
Insertion loss 0.5dB or less
Cut off [15kHz] 95dB Min.
Voltage proof 1 Min. at AC500V
Insulation resistance 50Mohm or more at DC250V
Max rating 0.2W (Linear taper), 0.1W (Other taper)
Maximum input voltage DC30V or less
Sliding noise level 47mV or less (by JIS C 6443)
Sliding life 100,000 Cycles Min. (18cycles/min, Sliding noise level: Less than 100mV)

Mechanical Specifications (Initial Value)

Mechanical specifications (Initial value) LSVH-1100 Series LSVH-6100 Series
Travel (Stroke) length 100mm ±0.5mm 60mm ±0.5mm
Operating force 0 to 0.1N (Standard)
0.1 to 0.4N (High operating force)
Strength Nut-Attached 100Ncm
Attached parts M3 screw (Length: Panel thickness + 3mm)
Stopper strength 30N
Push-pull strength 30N
Alignment to the center ±0.5mm (State not to pressure control-bar, Measurement position: Mounting surface)

General Specifications

General specifications LSVH Series
Temperature range -10 to +70 degrees C (Operating), -15 to +75 degrees C (Storage)
Relative humidity 90%RH (No condensation)

REQUEST QUOTATION

PAYMENT

payment-methods

 

TOOLS & EQUIPMENT

Lifting
Eagle Clamp | Eagle Jack | Elephant | Endo Kogyo
Japan Clamp | Kanetec | Jung | KITO | Katsuyama Kikai
Kondotec | Miki Netsuren | Sanei Seiki | Taiyo

Hand Tools
Bix | Miyakawa | Nakatani Kikai | Ogura | Osakada Tool
Super Tool | TONE | Yutani

Tape
Kamoi | Kikusui | Misuzu | Nirei | Okamoto | Taiho | Teraoka

Measurement
Hasegawa | Kawaki | Kett | KGK | Line Seiki | Nagano Keiki
Niigata Seiki | Obishi Keiki | RSK | Ryoden Shonan | Sanko
Sanwa Supply | Showa Seisakusho | Showa Sokki
SK Sato | Tokyo Keiso | Tokyo Sokushin

Safety Tools
Fujii Denko | Shigematsu | Titan

Welding
Asahi Weldex | Daihen | Koike | Nissan Tanaka

Drilling
Dijet | Kansai Kogu | Nitto Kohki | Okazaki Seiko | Takeda

Chemical
Cemedine | DaitoNippon Grease | Taseto

Other Tools
Hammer Caster | Kitagawa | Matsuda Seiki | Misuz | Sanritsu
Sanyutec | Shizuoka Seiki | Toyo Kensetsu Kohki | Yamamoto
Yamari

PLANT FACILITIES

Facilities
Acokk | Bunkaboeki | Horiuchi | Konan | Murakoshi
Murakoshi Industries | Nesstech | Nihon Flux | Nikkin Flux
NFK | Omega System | Organo | Taiyo Parker | Toyo Mic

Pump
Dynaflo | Ebara | Honda Kiko | KyowaMusashino
Tsurumi

Valve
Astam | Kyowa Iron | Nachi | Nippon Daiya | Sawada
Wasino Kiki | Yoshitake

Electricity
Arkon | Asahi Bagnal | Gentos | Iwasaki | Kokosha | U_RD

CONSTRUCTION

Concrete Work
Daia | EXEN | Japan Life | Mikasa | Okasan Kiko | Taiheiyo

Railway Work
Kyoei | Sanwa Tekki | Teikoku | Toko

Scaffolding
Bullman | Okabe | Rikiman | Tsugaru

High Tension Bolt
Dong Ah | KPF | Nippon Steel Bolten | Nippon Fastener

Bolt & Nut & Washer
Hard Lock | Kishu Fastener | Matsukin | Mori Kozai
Nakaumi | Naniwa | Ogawa | Otani | Sudo | Toneji

STEEL MATERIAL

Steel & other Material
Dongil | JIS Standard | DSR | Sumitomo Wire | Winoa IKK

Pipe
Benkan

Return Top