Toyo Keiki
TOYO KEIKI GP and HP Series Temperature Transducer
Product Made In Japan
Manufacturer: Toyo Keiki
Model: GP and HP Series
CGP-□: As a temperature sensor the resistance temperature detector is a temperature-DC conversion device.
Generous input specifications. ・From -200℃ to +500℃.
Photo couple provides complete insulation between input and output-the influence of common mode noise is excluded and stable operation is ensured (AC 2000V,1 min.).
Linearizer is standard. ・Linearity below±0.2%.
The influence of connecting cables is excluded. -Resistance temperature detector drives a constant, the type of measurement errors that are caused by the use of a connecting cable do not happen.
It was equipped with a burnout function. ・Sensor circuit failure immediately detected and output.
Plug-in type makes upkeep and configuration changes simple.
Specification
INPUT | OUTPUT | AUXILIARY POWER SUPPLY |
---|---|---|
Platinum resistance temperature detector, 3-lead type: Pt100Ω, JPt100Ω. Standard six bands of measured temperature range. Regulated sensor current: DC 2mA | 8 standard type of output are available. Burnout: Upper | AC 100/110V ±10% 50/60Hz approx. 3 VA AC 200/220V ±10% 50/60Hz approx. 3 VA DC 24V ±10% approx. 3 W DC 100/110V ±10% approx. 3.5 W DC 48V (38-62V) approx. 3 Wtypes are immediately available. For types not listed above contact a company representative. |
Available resistance temperature detectors Platinum(Pt, JPt)100Ω (0°C) -input span of over 50 °C When resistance temperature detectors not conforming to JISC 1604-1997 are specified please indicate the resistance line curve. |
Available with Max. voltage output 10V (600Ω~∞) Max. current output 20mA (0-550Ω) The burnout value may be lowered according to your needs. |
Connection Diagram
Specified Character
(1) Available resistance temperture detectors
Platinum(Pt,JPt)100Ω -input apan of over 50℃
Platinum(Pt)50Ω -input span of over 100℃
at JIS C 1604-1997(resistance temperature detector)
As well as nickel,platinum-cobalt,and copper resistance tempereture
detectors that conform to JIS C 1604-1997 are also available;
please contact a company representative and explain your need.
Input system 3-lead type (permissible line resistance,200Ω per lead)
(2) Regulated sensor current
DC 2mA
(3) Tolerance
±0.5% of output span.(Ambient temperature 23℃)
(4) Effect of temperature
Within ±0.2% of output span. (For 23℃±10℃ variations)
(5)Effect of auxiliary power supply
Within ±0.1% of output span. (For rated voltage ±10℃ variations)
(6)Effect of load resistance
Within ±0.05% of output span. (For load resistance range)
(7) Output ripple
Within 0.5%p-p of output span.
(8) Response time
Shorter than 0.5sec. (Time to 99% output)
(9) Dielectric strength
2000V AC,1min.(50/60Hz) (Between input,output,auxiliary power supply and external case)
(10) Insulation resistance
Higher than 100MΩ at 500V megger. (Between input,output,auxiliary power supply and external case)
(11) Built-in Functions
Isolation (photo-couple method)-standard
Linearizer (linearity within±0.2%)-standard
Burnuot function-In the standard specification burnout is set for when the following upper limit is exceeded:when the
output value=max.output value+10~15% of the output span(e.g.,21.6~22.4mA when the output is 4~20mA).
The burnout value may be lowered according to your needs.
(12) Weight
Approx.410g
DESIGNATION ITEM AT ORDER
1. TYPE AND AUXILIARY POWER SUPPLY | 2. INPUT | 3. OUTPUT | |
---|---|---|---|
CGP—□ | —□ □ | —□ |
AUXILIARY POWER SUPPLY | |
---|---|
1 | DC 24V |
2 | AC 100/110V 50/60Hz |
3 | AC 200/220V 50/60Hz |
5 | DC 100/110V |
6 | DC 48V |
9 | OTHER |
TEP.SENSOR | INPUT | ||
---|---|---|---|
1 | Pt 100Ω | 1 | 0 – 100°C |
2 | JPt 100Ω | 2 | 0 – 200°C |
3 | 0 – 300°C | ||
4 | 0 – 400°C | ||
5 | -50 ~ 50°C | ||
6 | -100 ~ 200°C | ||
9 | OTHER | 9 | OTHER |
OUTPUT | LOAD RESIS. |
---|---|
DC 0 ~ 100mV | 600Ω ~ ∞ |
DC 0 ~ 1V | 600Ω ~ ∞ |
DC 0 ~ 5V | 600Ω ~ ∞ |
DC 0 ~ 10V | 600Ω ~ ∞ |
DC 1 ~ 5V | 600Ω ~ ∞ |
DC 0 ~ 1mA | 0 ~ 10kΩ |
DC 0 ~ 10mA | 0 ~ 1kΩ |
DC 4 ~ 20mA | 0 ~ 550Ω |
OTHER OUTPUT |