UNIKA GE-165 (Cartridge Type) Resin A

Manufacturer: UNIKA

Model: GE type (Resin cartridge), GE type exclusive parts, Installation specifications, GE-165 TOOL BOX SET, Push pump, Metal brush, Extension nozzle(including three), Plastic sleeve (including 10 pieces)

■Can be used for various bolts, sizes and shapes of different reinforced steels.
■Used extensively for concrete, brick, stone material and hollow base material.
■Demonstrates stable fixing strength because primary material and hardening agent are constantly mixed by mixing nozzle.
■Adopts a highly alkali resistant epoxy acrylate resin.

<Code>
GE-165
(180*50*250)

Uses

Concrete•Stone material•Hollow base material•ALC

Installation method

Drill vertically to target surface with the determined preparation diameter and preparation hole depth.
Use a dust collector or blower to thoroughly remove chips in the hole.
Remove chips adhered in the hole using a brush, and use a dust collector or blower to clean in the hole again.
Insert the nozzle down to the hole bottom and fill resin.
Insert the bolt down to the hole bottom while slowly turning it by hand.
Do not move the anchor bolt within the determined hardening time after embedding.

■Uses

Foundation work for iron frame, Passage construction work, Tunnel construction work, Installation for vibrating machines.

■Structural Drawing

Structural Drawing

■Installation specifications

Nominal diameter(mm)	M8	M10	M12	M16	M20	M22	M24
Preparation hole diameter(mm)	10.0	12.0	14.0	18.0	24.0	25.0	28.0
Embedment depth(mm)	80	90	110	130	170	190	210
Required resin amount(ml)	4	6	9	15	42	43	66
Recommended tightening torque(Nm)	10	20	40	80	120	140	160
Number of pieces installed(Pcs)	31	21	13	8	2	2	1

*The number of pieces installed indicates the target number taking into consideration a loss rate of 20%.

■Installation Example

Continuous thread bolt
Plastic sleeve

■Shape of bolt used

Shape of bolt used

Cannot be used for a round bar. Use bolts which have irregularity on a surface such as a continuous thread bolt and different shape bar steel.

■Guideline for hardening time

Temperature(℃)	-5	5	15	25	35
Use time(minutes)	40	20	9	5	3
Hardening time(minutes)	180	90	60	30	20

(Do not move the anchor reinforcement within the hardening time.)

■Plastic sleeve installation specifications

Nominal diameter(mm)	M8	M10	M12
Preparation hole diameter(mm)	16.0	16.0	20.0
Matching sleeve(Code)	RA-P1685	RA-P1685	RA-P2085
Required resin amount(ml)	30	30	40

Avoid direct sunlight and store in a well-ventilated place where the temperature does not rise so high.
(Never raise the temperature above 40℃. Always keep the temperature in the range of 5 to 25℃.)
Do not bring close to fire or high temperature objects.
Cartridge can be stored until the expiration date for use under standard storage conditions.
Wear protective equipment (such as protective glasses and mask) when using.
When resin adheres to skin, irritation may occur in rare cases. Take action such as immediately wiping and rinsing with a hot soapy solution.
In addition, if resin gets into eyes, immediately rinse with a large amount of water and seek medical attention.

Make sure to provide the drilling diameter and drilling depth as described in the specifications.
Make sure to use both a metallic brush and blower to sufficiently clean inside the hole.
Make sure to mount the mixing nozzle with it just before use.
Make sure to discard first approximately 20~30cc at a time of first use and nozzle replacement. (Mixing improperly may result in reduction in strength.)
This cannot be used for a steel bar with no irregularity such as a round bar.
Refer to the scale on the cartridge label for discharge resin amount.
Do not move the bar steel nor apply load within the determined hardening time.
SPECIFICATIONS
GE type (Resin cartridge)
Size Capacity(ml)

GE-165 165
GE type exclusive parts
Product name Size Matching cartridge

Mixing nozzle(3 Pcs.) RA-MX3 GE

Injection gun 165 RA-GUN165 GE-165
Installation specifications

Use bolt different shape reinforced steel	Preparation hole diameter (mm)
M8	10
M10	12
D10	13
M12	14
D13	15
M16	18
D16	20
M20	24
D19	25
M22	25
D22	28
M24	28
D25	32
M30	35
D29	38

GE-165 TOOL BOX SET

Product name	Content(Pc.)	JAN Code
TB-165D(with drill)	GE-1654 Injection gun 1651	4.98927E+12
	SDS Plus UX (12.0X160/14.0X210)*each 1
Standard set product	Mixing nozzle6 Plastic sleeve 16855 Push pump*1 Metal brush(10/13/18) each 1

■Related items
Push pump
Size Specifications

RA-PUP (Nozzle diameter)

10mm

(Hose length)

270mm
Metal brush
Size Specifications

RA-MB10 Φ10*300

RA-MB13 Φ13*300

RA-MB18 Φ18*300

RA-MB28 Φ28*300
Extension nozzle(including three)
Size Specification

RA-EXP3 Φ8×1m
Plastic sleeve (including 10 pieces)
Size Specifications

RA-P1685 16*85(M8/10)

RA-P2085 20*85(M12)