, , ,

Line Seiki G62 Series Preset Counter

Product Made in Japan
Manufacturer: Line Seiki
Model: G62 Series

G62 Series Preset Counter

Model

ModelsFiguresPreset LevelInput
G62-101411 InputAdd / Subtract Input
G62-1022 Input90°Quadrature / Individual add, subtract Input
G62-11121 InputAdd / Subtract Input
G62-1122 Input90°Quadrature / Individual add, subtract Input

Description of G62 Series

The G62 Series offers a preset counter in a 60 x 60 panel with options for single or dual levels and has a cut-out size of 54 x 54mm. It features a bright two-line Red LED display, making it visible even in dim areas.

The primary display presents the count value, while the secondary one shows the preset value. People trust its consistent performance, as it can smoothly take in different input signals and impressively counts at a rapid speed, reaching up to 10kHz. When it reaches the preset value, the counter signals out, either through its built-in relay or an NPN Open collector.

Adjusting preset values is straightforward with the front panel button.The device draws its power from an AC100-240V source, and it also has a separate DC12V supply specifically designed to support sensors.The G62 ensures data safety with its internal EEPROM memory, even if power cuts off unexpectedly.

The G62 can operate in multiple modes with diverse output configurations. You can reset it directly from the front panel, remotely, or use the auto-reset. It also offers features like prescale settings, adjustable decimal points, and key protection. The front panel effectively keeps out dust and splashes, while terminal screws strengthen the wiring connections, ensuring they remain secure.

Specification of G62 Series

ModelsG62-101, 102G62-111、112
Preset Level1 Level2 Level
DisplayRed LED, Count figures: 10.0 x 5.5mm Editing figures: 8.0 x 4.0mm
Preset Range0 – 9999
Input1 input type: Add / Sub input (selectable by dip-switch)

2 input type: 90°Quadrature / Individual add, sub. input (selectable by dip-switch)

Input MethodNon-contact input : Open collector / Contact input : Relay, Microswitch
Count SpeedNon-contact input : 10 kHz (with Prescale: 6kHz max.)* / Contact input : 25 Hz maximum
Pulse WidthNon-contact input : 50 msec minimum. / Contact input : 20 msec minimum
Make (Duty)1 : 1
Output TypeContact output : Relay Type 1A only (AC250V, 0.5A / DC30V, 2A maximum Load)

Non-contact output : NPN open collector (DC30V, 100mA maximum) *for each output

Output Time0.1 sec or latch. (However, in Auto-reset mode, output time will be 0.1 sec, even if set to latch).
Output Delay10kHz: 5m/sec maximum
ResetFront reset, Remote reset (50msec min.), Auto-reset
Inhibition FunctionWhen the Inhibition terminals are enabled, count input, preset editing, and front reset are disabled.
Preset LampNoneTurns on while each preset value is shown on the display.
Operation ModeOverrun / Auto-reset
Decimal Point Positio4 digit : 0 / 0.0 / 0.00

6 digit : 0 / 0.0 / 0.00 / 0.000 / 0.0000

Output LampTurns ON during output time
MemoryE²PROM (10 years. retention, 10,000 times)
Power Source for SensorDC12V 100mA maximum
Power SourceAC100 – 240V -15%/+10%
Power ConsumptionApproximately 5VA
Operating Temperature-10 – +50°C (non-freezing)
Operating Humidity45 – 85%RH (non-condensing)
WeightApproximately 240g

Front Panel And Rear Terminals

Operations

In entering the setting mode to edit the preset values, make sure that the key protect feature is disabled by unshorting terminals No. 9 and No. 10.

Setting the Preset Value

  • <1 Level Preset>

  • <2 Level Preset>

Sample Operation

  • <1 Level Preset>

  • <2 Level Preset>

Wiring

Dip-Switch

Application

Product Counting

Counters can be used for counting, sorting and packaging various products.

Cut-to-length operation

Counters and CT1/CS pulse generators can be used for cut-to-length operation for textiles, paper, plastic films and so on.

Length Measuring

Counters and rotary encoders can be used for measuring the length of textiles, paper, plastic film and so on.


REQUEST QUOTATION

PAYMENT

payment-methods

Return Top