,

Orientalmotor L Series AC Speed Control Motors Equipped with DSC Series Rack-and-Pinion System

Made in Japan
Manufacturer: ORIENTAL MOTOR CO., LTD.
Model: L Series

Linear Motion Mechanism Can be Easily Constructed

Easy Construction of Compact Linear Motion Mechanism

The rack-and-pinion system can easily convert the rotation of the motor into linear motion.
Although the linear motion mechanism part is compact in design, it can transport a large load due to its high strength processing.

Structure of Rack-and-Pinion System

Structure of Rack-and-Pinion System

Movement of Rack-and-Pinion System

The gear (deceleration part) receives the motor of the pinion shaft, and further transmits it from the pinion gear to the rack to convert it into linear motion.

Reduces Startup Time From Design

By using Oriental Motor’s rack-and-pinion system, the number of components used can be reduced, significantly reducing the man-hours required for design and assembly compared to producing in-house.

Comparison of the Number of Components

[If Build In-House]                                        [For Rack-and-Pinion System]
If Build In-House    Rack-and-Pinion System
Equipment Startup Times Comparison
If Build In-House

Value Raise/Lower Speed Control

Vertical Operation From 58,800 JPY

Transportable mass of 6.6 kg~67 kg available, combining the simple structure rack-and-pinion system with AC speed control motors. Reasonable prices for transporting heavy loads.

Total amount for rack and pinion motor and speed controller.

Maximum Stroke 1000 mm

A variety of strokes are available to suit your equipment.

Maximum Stroke 1000 mm

3 Variable Speed Ranges Selectable According to Usage

Equipped with AC Speed Control Motor DSC Series that can control speed for vertical operation.
Choose from 3 variable speed ranges for each frame size.

Transportable Mass and Variable Speed Range (For 60 Hz)

Frame Size 60 mm                                                                Frame Size 80 mm
Transportable mass and variable speed range (For frame size 60 mm))  Transportable mass and variable speed range (for 80 mm frame size)

Sensor is required for setting the rack stop position.
2 types are available: “Photomicrosensor Set” and “Limit Switch Set” that enable back-and-forth motion with easy installation.

Compact Speed Controller Provides Comfortable Speed Control of Linear Motion Mechanism

Visualization of Linear Motion With Digital Display

Controller body allows monitoring of rack speed, alarm, warnings, and I/O status, as well as various settings and controls.

Speed and Other Settings are Shown and Can be Entered Directly

[Display of rack speed]
The rack speed can be displayed by setting the gear ratio for each product in the “gear ratio parameter” of the speed controller.

Compact Motor Controller

The volume is 63 % smaller than a general inverter.

Compact Motor Controller

Speed Control (4 speeds)

4 units of operation data can be set, and can be switched with I/O during operation.

Speed Control (4 speeds)

Acceleration/Deceleration

Makes the motor movement at start/stop smoother. It is possible to set acceleration/deceleration differently for each of the 4-speed data units.

Acceleration/Deceleration

Bi-Directional Operation

Performs the operation according to the command for rotation direction.

bi-directional operation </figure> </li> <li> <h4 class=Instantaneous Bi-Directional Operation

Instantaneously switches the rotation direction of the motor while operating.
(Short cycle change conditions can be created)

Instantaneous Bi-Directional Operation

Instantaneous Stop

Stops the operating motor instantaneously.
(Short cycle run/stop conditions can be created)

Instantaneous Stop

External Speed Setting Input is Possible

External Speed Setting Input is Possible

Multi-Motor Control (20 units max.)

A single external speed potentiometer can operate a max. of 20 units in parallel.
Fine adjustment of each motor’s speed can be performed by changing the controller’s parameters.

Multi-Motor Control (20 Units Max.))

Speed Range Control

It is possible to limit the speed setting in advance with the speed range.

Speed Range Control

Applications

The rack-and-pinion system, which can be applied to a variety of applications, is a user-friendly product that can be selected as if it were a component.

Horizontal operation, vertical operation

By changing the mounting surface, it is possible to switch usage to either horizontal or vertical operation.

vertical operation

Vertical operation is also easy. With an electromagnetic brake, fall prevention and load holding is allowed.

 L Series

Using the screw holes at the end of rack simplifies the fastening of loads and rack fixing.

High Thrust

High thrust can also be used to lift the press or table as is.

Vertical Opening and Closing of Heavy Doors, Etc.

The open/close speed can be freely adjusted, even where a heavy door is opened or closed vertically.

REQUEST QUOTATION

PAYMENT

payment-methods

Return Top