,

SHOWA SOKKI 4001B-50 Charge amplifier for force sensor and pressure sensor

Made in Japan
Manufacturer: SHOWA SOKKI
Model: 4001B-50

Features

  • This is a charge amplifier for piezo-type force sensors and pressure sensors.
  • Unlike general charge amplifiers, this charge amplifier can measure almost from DC.
  • The discharge time constant can be switched between LONG and SHORT, and low frequency response characteristics can be selected.
  • The charge amplifier Model-4001B-50 is suitable for the following applications: ・”Force” measurement with a wide dynamic range
    ・Measurement of impact “force”
    ・Measurement of engine combustion pressure
    ・Measurement of compressor pressure, etc.

Product photo

Example of connecting a ring type “force” sensor to a charge amplifierMulti-channel configuration
4001B-50-4CH
Ring type “force” sensor
(1-axis and 3-axis)

Specification

Measuring rangeDetector sensitivity
10,20,50,100,200,500,1000UNIT/VOLT when 1.00~9.99pC/UNIT
Range accuracyWithin 1.5% (at 80Hz)
Frequency characteristicRange 100 to 1000 DC to 50kHz Within 5%
Range 50 DC to 40kHz Within 5%
Range 20 DC to 20kHz Within 5%
Range 10 DC to 10kHz Within 5%
Discharge time constant (TC)SHORT range x 0.1sec
(Feedback resistance 109Ω)
LONG range x 1000sec
(Feedback resistance 1013Ω or more)
low frequency cutoff0.16/ Discharge time constant (TC) Hz (-3dB)
LinearityWithin ±0.1%
Input referred noise0.1 pCrms or less
maximum driftAdjustable to ±0.03 pC/s or less at DC BAL
(after 20 minutes of warm-up)
reset error±0.5pC or less
Reset switching time500msec or more
Maximum input charge±100,000pC (slew rate 5,000pC/μs)
output voltageMaximum ±10V
output current±5mA maximum
output resistance100Ω
Output calibration signalSupplied from power supply MODEL-4001-10A 0 to 10VDC
with variable CAL/OP selector switch (rear)
overload0 to 50°C, 80% RH or less
temperature, humidity range0 to 50°C, 80% RH or less
power supplyCharge amplifier ±15VDC, 20mA or less
When using AC adapter AC100V±10V
When using power supply unit AC100V±10V
massCharge amplifier MODEL-4035-50310g/CH
​​Power supply MODEL-4001-10A 800g
Case for 6CH MODEL-4001-26: 1300g

Applicable sensor specifications MODEL-2101/2103

itemMODEL-2101 (1 axis)MODEL-2103 (3 axes)
Measurement range0 to 80 kNX,Y:-20~+20kN
Z:-40~+40kN
(Z):0~+200kN
charge sensitivity-4.4pC/N(X,Y) -7.6 pC/N
(Z) -4.0 pC/N
insulation resistance1013Ω or more1013Ω or more
Linearity (Typ)±2%FS or less±3%FS or less
threshold0.01N or less0.001N or less
Recommended preload40 kN160 kN
Operating temperature limit-20 to +60°C-20 to +60°C
groundcase groundcase ground
methodpiezoelectricpiezoelectric
Element materialcrystalcrystal
Outer case materialStainless steelStainless steel
output terminalminiature connectorminiature connector
Body mass35g270g
*Note: Values ​​in ( ) are without preload

 

REQUEST QUOTATION

PAYMENT

payment-methods

Return Top