,

Tokyo Ko-on Denpa LMA5 Series Motorized Control Fader

Made in Japan
Manufacturer: Tokyo Ko-on Denpa Co., Ltd.
Model: LMA5 Series

Features

Direct print resistor element used (Special surface treatment).
Vertical style control-bar design.
PCB Terminal style.
All models include a touch sense track.

LMA5 Series

Electrical Specifications (Initial Value)

Electrical specifications (initial value) LMA5 Series
Products LMA5-11**-B*-* LMA5-61**-B*-*
Number of circuits / Type of output law 1
Law: Linear taper
Circuit method (Output law) Potentiometer circuit
Total resistance (1-3) 10kohm, 5kohm
Total resistance tolerance ±20%
Absolute linearity ±5% (The travel is divided into 10 sections and 11 positions are measured.)
Residual voltage (1-2), (2-3) 20mV or less
Residual resistance (1-2), (2-3) 50ohm or less (Reference values)
Touch sense track contact resistance 30ohm or less (Between terminal T and Control-bar.)
Voltage proof 1 Min. at AC500V
Insulation resistance 50Mohm or more at DC100V
Max rating 0.2W
Maximum input voltage DC30V or less
Sliding noise level 47mV or less (by JIS C 6443)
Sliding life 100,000 Cycles Min. (18cycles/min, Sliding noise level: Less than 100mV)
Drive motor data DC8V Iron cored motor : Input voltage: DC5V – 11.5V (Nominal DC8V),
Stall current: 0.5A or less [FF-050SB-09250 : MABUCHI MOTOR Co., Ltd.]

Mechanical Specifications (Initial Value)

Mechanical specifications (Initial value) LMA5-1101 Series LMA5-6101 Series
Travel (Stroke) length 100mm ±0.5mm 60mm ±0.5mm
Operating force 0.1 to 0.3N
Strength Nut-Attached 100Ncm
Attached parts M3 screw (Length: Panel thickness + 3~5mm)
Stopper strength 30N
Push-pull strength 30N
Alignment to the center ±0.5mm (State not to pressure control-bar, Measurement position: Mounting surface)

General Specifications

General specifications LMA5 Series
Temperature range -10 to +50 degrees C (Operating), -15 to +60 degrees C (Storage)
Relative humidity 80%RH (No condensation)

 

REQUEST QUOTATION

PAYMENT

payment-methods

 

TOOLS & EQUIPMENT

Lifting
Eagle Clamp | Eagle Jack | Elephant | Endo Kogyo
Japan Clamp | Kanetec | Jung | KITO | Katsuyama Kikai
Kondotec | Miki Netsuren | Sanei Seiki | Taiyo

Hand Tools
Bix | Miyakawa | Nakatani Kikai | Ogura | Osakada Tool
Super Tool | TONE | Yutani

Tape
Kamoi | Kikusui | Misuzu | Nirei | Okamoto | Taiho | Teraoka

Measurement
Hasegawa | Kawaki | Kett | KGK | Line Seiki | Nagano Keiki
Niigata Seiki | Obishi Keiki | RSK | Ryoden Shonan | Sanko
Sanwa Supply | Showa Seisakusho | Showa Sokki
SK Sato | Tokyo Keiso | Tokyo Sokushin

Safety Tools
Fujii Denko | Shigematsu | Titan

Welding
Asahi Weldex | Daihen | Koike | Nissan Tanaka

Drilling
Dijet | Kansai Kogu | Nitto Kohki | Okazaki Seiko | Takeda

Chemical
Cemedine | DaitoNippon Grease | Taseto

Other Tools
Hammer Caster | Kitagawa | Matsuda Seiki | Misuz | Sanritsu
Sanyutec | Shizuoka Seiki | Toyo Kensetsu Kohki | Yamamoto
Yamari

PLANT FACILITIES

Facilities
Acokk | Bunkaboeki | Horiuchi | Konan | Murakoshi
Murakoshi Industries | Nesstech | Nihon Flux | Nikkin Flux
NFK | Omega System | Organo | Taiyo Parker | Toyo Mic

Pump
Dynaflo | Ebara | Honda Kiko | KyowaMusashino
Tsurumi

Valve
Astam | Kyowa Iron | Nachi | Nippon Daiya | Sawada
Wasino Kiki | Yoshitake

Electricity
Arkon | Asahi Bagnal | Gentos | Iwasaki | Kokosha | U_RD

CONSTRUCTION

Concrete Work
Daia | EXEN | Japan Life | Mikasa | Okasan Kiko | Taiheiyo

Railway Work
Kyoei | Sanwa Tekki | Teikoku | Toko

Scaffolding
Bullman | Okabe | Rikiman | Tsugaru

High Tension Bolt
Dong Ah | KPF | Nippon Steel Bolten | Nippon Fastener

Bolt & Nut & Washer
Hard Lock | Kishu Fastener | Matsukin | Mori Kozai
Nakaumi | Naniwa | Ogawa | Otani | Sudo | Toneji

STEEL MATERIAL

Steel & other Material
Dongil | JIS Standard | DSR | Sumitomo Wire | Winoa IKK

Pipe
Benkan

Return Top