Drilling And Cutting, Japan, Unika
UNIKA C Rooty Anchor
Manufacturer: UNIKA
Model: C type mm size (Trivalent Chromate Treatment)/ C type Inch size (Trivalent Chromate Treatment)
■Simply hammer in the pin. Just by looking at the pin, completion of anchor can be confirmed.
■As the thread and the anchor main body are the same in diameter, anchoring without rattling is possible by drilling from above fixture.
| Thread dia | Tightening Torque |
|---|---|
| M6 | 5 N・m |
| M8, W5/16 | 12 N・m |
| M10, W3/8 | 24 N・m |
| M12, W1/2 | 42 N・m |
| M16 | 100 N・m |
| M20 | 200 N・m |
USES
Concrete
- Drill preparation hole.
- Position anchor.
- Strike pin with hammer.
- Anchor attached with open lags.
■Installation explanatory video
■Uses
Suited for all kinds of fixture attachments including construction, electrical, sanitation, airconditioning/heating, signboard attachment, seat attachment, and machine installation works.
■Structural Drawing
■Use Examples
- Protective clothing including safety glasses and helmets must always be worm when installing.
- Drill perpendicularly into target surface.
- Compared with anchor insertion depth, drill holes should be 5mm deeper for M6, M8, M10; 7mm deeper for M12; 10mm deeper for M16; 15mm deeper for M20.
- Drilling preparation holes too shallow will break or bend core rods.
- Use blower throughly.
- Always set nut before hammering.
- Use a hammer appropriate for the anchor size.
- JCAA Product Certification Mark
- Products with this certification mark satisfy the evaluation and certification standards specified
by the Japan Construction Anchor Association (JCAA).
SPECIFICATION
C type mm size (Trivalent Chromate Treatment)
| Size | Dia (outside diameter) | Size | Dia (outside diameter) |
| C-645 | M6 | C-1260 | M12 |
| C-660 | C-1270* | ||
| C-840 | M8 | C-1280* | |
| C-850* | C-1290* | ||
| C-870* | C-1210* | ||
| C-890* | C-1212* | ||
| C-810* | C-1215* | ||
| C-1050 | M10 | C-1680 | M16 |
| C-1060* | C-1610* | ||
| C-1070* | C-1612* | ||
| C-1080* | C-1615* | ||
| C-1090* | C-1619* | ||
| C-1010* | C-2013* | M20 | |
| C-1012* | C-2015* | ||
| C-1015 | C-2019* |
*JCAA certified product
*Special dimensions for both C and SC types can be produced to order.
C type Inch size (Trivalent Chromate Treatment)
| Size | Dia (outside diameter) |
| C-2550* | W5/16 |
| C-3060* | W3/8 |
| C-3090* | |
| C-4870* | W1/2 |
*JCAA certified product
*Special dimensions for both C and SC types can be produced to order.
*Maximum extraction strength values are values measured by UNIKA and not standard values.
Related Products
-
Nissho Astec TP-Y Tubes & Pipes
-
LOBTEX J-PWP Power Pliers
-
DIJET RNMS-U-C Series Short Stub Straight Shank Tapper Neck Type
-
Hammer Caster 429SOS-NRB Middle Size Nylon Wheel
-
SAKUSAKU 2SS-20D 10.0S Carbide Square End Mill 2-Flute
-
Okazaki Seiko BCER Top Solid Carbide End Cutting Reamers (Straight Shank)
REQUEST QUOTATION
PAYMENT
LINK
