Drilling and Cutting, Japan, Unika
UNIKA DJW Type Cordless Diamond Core Bit
Manufacturer: UNIKA
Model: DJW Type(Semi-dry wax was enclosed)
- When using the specially developed wax, no water cooling is required.
- ■ This special diamond production method is ideal on an impact electric driver.
Offers fast drilling and long life. - ■ With the positioning guide, stable drilling is assured.
*The positioning guide is sold optionally.
◆Applicable Electric Tool: Cordless Drill / Driver Drill / Electric Drill(under 400W)
(663KB)
Uses
Ceramic tile•Stone material tile• Hard tile•Granite stone•Marble• Roof tile
-
<DIA>
5.0-15.0mm
(70*72*185) -
<DIA>
20.0?35.0mm
(93×92×187)
*( ) The number inside is the package size. W*D*H(mm) As for size there is an the error of ±2mm depending upon the package.
■ Just apply the semi-dry wax to the drilling edge.
Due to the special cooling properties in the semi-dry wax, there is no need for using messy water when the wax is applied.
■ Drill Positioning Guide
Place the core drill bit in the V-slot and start drilling. While the drill is rotating, gently penetrate the material diagonally.
Once the diamond core drill bit totally penetrates the material 1-2 mm deep stop drilling and remove the guide. Then, continue drilling.
■ Drilling components
■ Hexagonal shank
Due to its 6.35mm HEX shank, stable holding and positioning is assured.
- Use the electric drill appropriate for the drill bit used.
- Make sure to turn off the main switch and take out the power supply plug from the socket before attaching and detaching the drill bit.
- Attach the drill bit by pushing in until it stops at the end of the chucking part of the drill, and clamp the drill bit tightly so that it will not loosen or come off.
- Wear protective glasses.
- Drill holes vertically against the drilled material surface.
- Read the instruction manual for the electrical drill before use and always observe instructions to ensure safe and correct operation.
- SPECIFICATIONS
- DJW Type(Semi-dry wax was enclosed)
-
Code Diameter(mm) DJW5.0X60S 5 DJW6.0X60S 6 DJW6.4X60S 6.4 DJW7.0X60S 7 DJW8.0X60S 8 DJW10.0X60S 10 DJW12.0X60S 12 DJW15.0X60S 15 DJW20.0X76S 20 DJW25.0X76S 25 DJW30.0X76S 30 DJW32.0X76S 32 DJW35.0X76S 35 
-
Positioning Guide V Code Matching hole Diameter(mm) JAN Code DJW-PGD-V 5.0-35.0 4989270128040 
During use and immediately after use, the core drill and cutting waste becomes very hot so take care of that to not touch it with bare hands.
In addition, after drilling porcelain shavings and used wax may be scattered around the work area, therefore prepare the surrounding area for it.
Related Products
-
Kyowa DBT-120A-8 for 120Ω Gauge Bridge Box Input Adapter
-
SAKUSAKU SDHL21120203 Holder For Grooving/Turning
-
Kyowa AS-10GA AS-GA Small-sized Small-capacity Acceleration Transducer
-
Tokyo Keiso STK4000 Series Sight Glass Type Flow Monitor
-
Super Tool RNB1719/1721/1921 Ratchet Wrench (With Bent Spear)
-
Nakatani Kikai NG75L(K)‐DRG Disc Grinder (Straight)
REQUEST QUOTATION
PAYMENT
LINK
