Make sure to mount the mixing nozzle with it just before use.Make sure to discard first approximately 20~30cc at a time of first use and nozzle replacement. (Mixing improperly may result in reduction in strength.)
This cannot be used for a steel bar with no irregularity such as a round bar.
Refer to the scale on the cartridge label for discharge resin amount.
Do not move the bar steel nor apply load within the determined hardening time.
Drilling and Cutting, Japan, Unika
UNIKA PE-400G Cartridge Type Resin A
Precautions on use
Manufacturer: UNIKA
Model: PE type
Features
You can use it for various bolts, sizes, and shapes of different reinforced steels.
Excellent in chemical resistance, and can be used for installation in water.
The mixing nozzle constantly mixes the primary material and hardening agent, demonstrating stable fixing strength.
Adopts high performance epoxy resin with no resin contraction. Also less odor and toxicity.
Uses
Concrete•Rock bed
- Drill vertically to target surface with the determined preparation diameter and preparation hole depth.
- Use a dust collector or blower to thoroughly remove chips in the hole.
- Remove chips adhered in the hole using a brush, and use a dust collector or blower to clean in the hole again.
- Insert the nozzle down to the hole bottom and fill resin.
- Insert the bolt down to the hole bottom while slowly turning it by hand.
- Do not move the anchor bolt within the determined hardening time after embedding.
Uses
Foundation work for iron frame, Passage construction work, Tunnel construction work, Installation for vibrating machines.
Structural Drawing
Installation specifications
| Nominal diameter(mm) | M8 | M10 | M12 | M16 | M20 | M22 | M24 |
|---|---|---|---|---|---|---|---|
| Preparation hole diameter(mm) | 10.0 | 12.0 | 14.0 | 18.0 | 24.0 | 25.0 | 28.0 |
| Embedment depth(mm) | 80 | 90 | 110 | 130 | 170 | 190 | 210 |
| Required resin amount(ml) | 4 | 6 | 9 | 15 | 42 | 43 | 66 |
| Recommended tightening torque(Nm) | 10 | 20 | 40 | 80 | 120 | 140 | 160 |
| Number of pieces installed(Pcs.) | 87 | 58 | 38 | 23 | 8 | 8 | 5 |
*Number of pieces installed is for reference number of pieces at a loss rate of 20%.
Shape of bolt used
You cannot use it for a round bar. Use bolts with surface irregularities, such as continuous thread bolts, and bar steels of different shapes.
Guideline for hardening time
| Temperature(℃) | 5 | 15 | 25 | 35 | 40 |
|---|---|---|---|---|---|
| Use time(minutes) | 100 | 60 | 40 | 25 | 20 |
| Hardening time(minutes) | 2400 | 1440 | 660 | 540 | 480 |
(Do not move the anchor reinforcement within the hardening time.)
Precautions on use
Avoid direct sunlight and store in a well-ventilated place where the temperature does not rise so high.
(Never raise the temperature above 40℃. Always keep the temperature in the range of 5 to 25℃.)
Do not bring close to fire or high temperature objects.
You can store the cartridge until the expiration date under standard storage conditions.
Wear protective equipment (such as protective glasses and mask) when using.When resin adheres to skin, irritation may occur in rare cases.
Take action such as immediately wiping and rinsing with a hot soapy solution.
In addition, if resin gets into eyes, immediately rinse with a large amount of water and seek medical attention.
Precautions on installation
Make sure to provide the drilling diameter and drilling depth as described in the specifications.
Use both a metallic brush and a blower to thoroughly clean inside the hole.
SPECIFICATIONS
PE type (Resin cartridge)
Size Capacity(ml) PE-400G 400 
- PE type exclusive parts
Product name Size Matching cartridge Mixing nozzle(2 Pcs.) RA-MX2PEGN PE-G Injection gun 400 RA-GUN400 PE-400G 
- Installation specifications
Use bolt different shape reinforced steel Preparation hole diameter(mm) M8 10 M10 12 D10 13 M12 14 D13 16 M16 18 D16 20 M20 24 D19 25 M22 25 D22 28 M24 28 D25 32 M30 35 D29 38 
■Related items
- Push pump
Size Specifications RA-PUP (Nozzle diameter) 10mm (Hose length) 270mm 
- Metal brush
Size Specifications RA-MB10 Φ10*300 RA-MB13 Φ13*300 RA-MB18 Φ18*300 RA-MB28 Φ28*300 
- Extension nozzle(including three)
Size Specification RA-EXP3 Φ8×1m 
