,

Maeda Koki MKCM Type Water Signal

Made in Japan
Manufacturer: Maeda Machinery Research Institute Ltd.
Model: MKCM Type

Features

  • Flow switch
  • Detects the flow of fluid and turns the switch ON or OFF at the specified flow rate.
  • *The switch is fixed (the setting cannot be changed later). A flow detector that checks the flow of fluid by the movement of a float inside a transparent tube that allows you to see the water flow at a glance.
  • Comes with a protective cover. The metal protective cover reduces the possibility of damage from external impacts.
  • No need to worry about the installation direction.Because a spring is used inside, the installation position can be freely changed, such as upward, downward, or sideways.

Models List

Model 
 Dimensions (mm) [ The overall width is a cast surface, so there may be individual differences]
Flow rate (L/min)
 Connection port size
full length 
Overall width 
Depth 
Minimum inner diameter
φmm
Specified range of operating flow rate
maximum
MKCM20-1TW-OFF
 Rc1/8
80
30
twenty two
6.5
 0.1 to 4
Ten
MKCM20-1TW-ON
MKCM20-2TW-OFF
Rc1/4
80
30
twenty two
6.5
 0.1 to 4
Ten
MKCM20-2TW-ON
MKCM20-3TW-OFF
Rc3/8
86
30
twenty five
6.5
 0.1 to 4
Ten
MKCM20-3TW-ON
MKCM30-2TW-OFF
Rc1/4
100
44
32
9.5
 0.5–10
20
MKCM30-2TW-ON
MKCM30-3TW-OFF
Rc3/8
104
44
32
9.5
 0.5–10
20
MKCM30-3TW-ON
MKCM30-4TW-OFF
Rc1/2
110
44
32
9.5
 0.5–10
20
MKCM30-4TW-ON
MKCM35-4TW-OFF
Rc1/2
124
49
44
 13.5
3–15
50
MKCM35-4TW-ON
MKCM35-6TW-OFF
Rc3/4
124
49
44
 13.5
3–15
50
MKCM35-6TW-ON
MKCM45-6TW-OFF
Rc3/4
142
62
50
18.0
5–30
100
MKCM45-6TW-ON
MKCM45-8TW-OFF
Rc1
142
62
50
18.0
5–30
100
MKCM45-8TW-ON

Standard Specifications

MKCM Type MKCM Type

SpecificationDetailsAdditional Information
FluidWater
Operating Flow RatePlease specify a flow rate value within the specified operating flow rate range above.
ConnectionRc female threadChange to R male thread. Combination with R male thread is also possible.
Heatproof temperatureMaximum 60°CHeat-resistant specifications (maximum 100°C) are also available.
Pressure resistance1MPaPressure-resistant specifications (up to 5 MPa) are also available.
Maximum Operating VoltageDC, AC 300V
Maximum current usedDC, AC 0.5A
Contact Capacity50VA
MaterialTransparent tubeAcrylicHeat-resistant and pressure-resistant products are made of brass tube (C3604). Heat-resistant and pressure-resistant products have a float that cannot be visually inspected.
Protective coverBC (gunmetal)Aluminum versions are also available.
FittingsC3604 (Brass)SUS products are also available.
SpringSUS304
Magnet included floatAcrylic or nylon
O-ringNitrile RubberHeat and pressure resistant specifications are made of fluororubber.
Reed switchCommercial goods
Lead wire (standard 200mm)Commercial goodsYou can also specify the length of the lead wire and change to a cab-tire cord.

Precautions when using flow switches

1. Precautions regarding magnetic fields

Reed switches are magnetic switches, so use them in a place where they will not be affected by magnetic fields.
If there is a magnetic material such as iron near a reed switch, it may cause it to malfunction.

2. Electrical wiring precautions

When wiring a flow switch, pay attention to prevent overcurrent from flowing through the reed switch due to poor earth wiring, etc.
Whenever possible, use the flow switch as an alarm detector.
When using in conjunction with other electrical equipment, be sure to take into consideration the impact of malfunction before handling.
The life of the reed switch will be extended if the operating voltage and current are kept as low as possible.
(Normally, the switch can be operated approximately 1 million times under conditions of 100V, 0.5A.)

REQUEST QUOTATION

PAYMENT

payment-methods

Return Top