,

OSC77FD530HF Tilting Flow Channel (300mm Wide)

Model: OSC77FD530HF

Features

– The channel is designed for studying the hydraulic flow phenomena

Under Frame

– The channel bed is an invert which rests on an H-beam under frame
– The invert has screws at interval for vertical and side adjustment of the invert to ensure that the channel bed is strictly straight an level through out the full length
– The length of the H-beam is about 6m
– This simplifies site installation as there is only one joint and is easier to ensure alignment of the channel
– The H-beam is supported by a fulcrum at one end and adjustable height support at the other end

Slope Adjustment

– The adjustable height supports use twin-screw
– Each screw is driven by a worm and wheel gearbox with a common motor
– A slope scale is provided at one end of the flume

Side Walls
– For safety reasons, the side walls are made of tempered glass or clear acrylic
– The walls are supported at the interval by brackets with a screw adjustment to ensure that the channel wall is straight and vertical
– Further, a set of small adjusting screws along the edge of each glass plate for fine adjustment is also provided to ensure that the walls are vertical, parallel and straight through out the channel length

Instrument Carriage
– Top rails made of stainless steel tubes are attached to the top angle on each wall of the channel
– Screws supporting the rails can be adjusted to ensure the uniform height and in a straight line
– A scale graduated in mm is attached along the full length of one top angle of the walls
– The instrument carriage is motorized
– Power out is available on the carriage

Head Tank
– The head tank is made of stainless steel and its sides and bottom are curved to ensure smooth flow into the channel
– Perforated plates are also provided in the head tank to further smoothen the flow

Head Tank
– The storage tank has adequate water to fill the full channel
– The standard storage tank is a stainless steel tank with a mobile ladder for model installation

Circulating Pump
– The pump seal is mechanical
– A geared butterfly valve is provided for accurate flow control

Flow Measurement
– A paddle wheel type flow sensor with two indicators, front and rear of the channel, is used for easy observation on flow adjustment
– A water meter is available as an option and may be used as a reference for flow indicator setting later

Model and Accessories

– All accessories and models have side seals to ensure no water seepage or leakage through the side of the models A wide variety of models and accessories are available as an option

Specifications

Model OSC 77FD 530HF
Flume dimensions   30cm wide, 45cm high and 12m long
Tilting adjustment   -1% to +3%
Side walls 6mmm tempered glass or 10mm clear acrylic
channel bed Stainless steel
Instrument trolley Motorized
Storage tank Stainless steel
Head tank Stainless steel with stilling baffles
Sluice gate Stainless steel, rack and pinion type, built-in at both ends of flume
Circulating pump 5.5kW with a maximum flow rate over 30 lps
Flow measurement Flow sensor and indicators
Power supplu 380V, 3Ph 50Hz or as required
Size   Approx. 250 x 1400 x 200 cm

REQUEST QUOTATION

PAYMENT

payment-methods

 

TOOLS & EQUIPMENT

Lifting
Eagle Clamp | Eagle Jack | Elephant | Endo Kogyo
Japan Clamp | Kanetec | Jung | KITO | Katsuyama Kikai
Kondotec | Miki Netsuren | Sanei Seiki | Taiyo

Hand Tools
Bix | Miyakawa | Nakatani Kikai | Ogura | Osakada Tool
Super Tool | TONE | Yutani

Tape
Kamoi | Kikusui | Misuzu | Nirei | Okamoto | Taiho | Teraoka

Measurement
Hasegawa | Kawaki | Kett | KGK | Line Seiki | Nagano Keiki
Niigata Seiki | Obishi Keiki | RSK | Ryoden Shonan | Sanko
Sanwa Supply | Showa Seisakusho | Showa Sokki
SK Sato | Tokyo Keiso | Tokyo Sokushin

Safety Tools
Fujii Denko | Shigematsu | Titan

Welding
Asahi Weldex | Daihen | Koike | Nissan Tanaka

Drilling
Dijet | Kansai Kogu | Nitto Kohki | Okazaki Seiko | Takeda

Chemical
Cemedine | DaitoNippon Grease | Taseto

Other Tools
Hammer Caster | Kitagawa | Matsuda Seiki | Misuz | Sanritsu
Sanyutec | Shizuoka Seiki | Toyo Kensetsu Kohki | Yamamoto
Yamari

PLANT FACILITIES

Facilities
Acokk | Bunkaboeki | Horiuchi | Konan | Murakoshi
Murakoshi Industries | Nesstech | Nihon Flux | Nikkin Flux
NFK | Omega System | Organo | Taiyo Parker | Toyo Mic

Pump
Dynaflo | Ebara | Honda Kiko | KyowaMusashino
Tsurumi

Valve
Astam | Kyowa Iron | Nachi | Nippon Daiya | Sawada
Wasino Kiki | Yoshitake

Electricity
Arkon | Asahi Bagnal | Gentos | Iwasaki | Kokosha | U_RD

CONSTRUCTION

Concrete Work
Daia | EXEN | Japan Life | Mikasa | Okasan Kiko | Taiheiyo

Railway Work
Kyoei | Sanwa Tekki | Teikoku | Toko

Scaffolding
Bullman | Okabe | Rikiman | Tsugaru

High Tension Bolt
Dong Ah | KPF | Nippon Steel Bolten | Nippon Fastener

Bolt & Nut & Washer
Hard Lock | Kishu Fastener | Matsukin | Mori Kozai
Nakaumi | Naniwa | Ogawa | Otani | Sudo | Toneji

STEEL MATERIAL

Steel & other Material
Dongil | JIS Standard | DSR | Sumitomo Wire | Winoa IKK

Pipe
Benkan

Return Top